04-05-2009
[SOLVED] Connecting to DHCP network with Realtek interface
Replaced network card
10 More Discussions You Might Find Interesting
1. IP Networking
Hi all,
I am experiencing a problem with dhcp broadcast packages. these broadcast packages are seen on bge1 and bge1:1 interfaces but somehow they are not seen at bge771001 interface which is second virtual interface on the bge1 interface.
I have a server on which I configured it as working... (2 Replies)
Discussion started by: ironoxide
2 Replies
2. Fedora
Hello all :confused:
I am using a Realtek RTL-8185 wireless lan controller on my Dell dimension 4800 to try to connect to the internet. my distro is fedora 11. I go to enable wireless and my computer freezes, I have done some upgrading and building on the computer for a year now but I have... (1 Reply)
Discussion started by: schizolinux
1 Replies
3. IP Networking
Hi,
I have a PC running Solaris 10 (hostname MARKUNIX) and a laptop running WinXP (hostname MARK-LAPTOP).
Both are connected to broadband via a router. IP addresses for each are determined via DHCP (192.168.1.nn) and I do not leave either on, 24x7.
I am running Oracle on MARKUNIX and... (1 Reply)
Discussion started by: ksdmnv
1 Replies
4. Ubuntu
hi,
can anyone tell me how to check if my interface is controlled by dhcp?
i tried with ifconfig command
ifconfig interfacename dhcp status
but its showing unknown host : dhcp error. (2 Replies)
Discussion started by: v1jay
2 Replies
5. IP Networking
Hi,
We currently operate a DHCP Server on Vxworks system.
It seems that the server is functioning only over the boot interface.
While trying to use it on a different interface the DHCP client messages seems to reach the interface but stay without response.
From a... (1 Reply)
Discussion started by: zohara
1 Replies
6. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
7. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
8. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
9. IP Networking
Let's say I have a home network containing a server that acts as the resident gateway and serves dhcp and dns requests. Laptop A is frequently connected and disconnected from the network as it is used as a travel computer. Is there a secure way to make sure that whenever laptop A is connected to... (3 Replies)
Discussion started by: Zygomorph
3 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
proto(4) Kernel Interfaces Manual proto(4)
NAME
proto - prototype job file for at
SYNOPSIS
DESCRIPTION
When a job is submitted to or the job is constructed as a POSIX shell script (see at(1)). The job file is created in as follows:
o creates a header describing the job as an job or a job. jobs submitted to all queues other than queue are listed as jobs. The header
is:
for an job, or
for a job.
o A set of POSIX shell commands is added to make the environment (see environ(5)) for the job the same as the current environment.
o then copies text from the prototype file to the job file, except for special variables that are replaced by other text:
Replaced by the current working directory.
Replaced by the current file size limit (see
ulimit(2)).
Replaced by the current umask (see
umask(2)).
Replaced by the time at which the job should be run,
expressed as seconds since January 1, 1970, 00:00 Coordinated Universal Time, preceded by a colon.
Replaced by text read by
from the standard input (that is, the commands provided to to be run in the job).
o When a job is submitted to queue queue, uses the file as the prototype file if it exists. Otherwise, it uses the file
EXAMPLES
The following file creates commands to change the current directory, file size limit, and umask in the job to their respective values as
they existed when was originally run. These commands are inserted before the commands in the job:
SEE ALSO
at(1), queuedefs(4).
STANDARDS CONFORMANCE
proto(4)