|
|
Sponsored Content
Operating Systems
Linux
Do linux have a device file for ETHERNET CARD.
Post 302303952 by iamjayanth on Saturday 4th of April 2009 03:42:14 AM
04-04-2009
|
|
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
5. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
8. Solaris
I do have a server (SUNV240) with Solaris 9, it has a PCI gigaswift ethernet card for fiber with SC connector, everytime I reboot the server the card won't link up unless I unplug it and plug it back again, for remote operations this is a hassle since sometimes reboots are needed and this card... (3 Replies)
Discussion started by: xe2bss
3 Replies
9. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
10. Red Hat
Unable To Activate Ethernet Network Device in RHEL 5.5 - e100 device eth0 does not seem to be presen
Hi All,
Could anyone please help to resolve the below problem.
I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error.
I spent 2 days for the above and go through with several suggestion found by googling. But no luck.
... (0 Replies)
Discussion started by: Tanmoy
0 Replies
LEARN ABOUT DEBIAN
input-linux-mouse
input-linux-mouse(7) GGI input-linux-mouse(7) NAME
input-linux-mouse - Direct mouse input SYNOPSIS
input-linux-mouse: [<mousetype>] [,<file>] [,[b<bauds>][r<rts>][d<dtr>]] DESCRIPTION
This input opens a file (usually a device file or pipe) and reads mouse protocol data from it. OPTIONS
mousetype Indicates what type of mouse is attached. The following types are supported: o ms, Microsoft : Two button Microsoft compatible mice. o ms3, IntelliMouse, mman+ : Serial Intellimouse or compatible. Supports four buttons for mice like the Logitech MouseMan+. o MouseSystems, msc : MouseSystems compatible (used in most 3-button mice). o Logitech, logi : Used in older Logitech serial mice. o mm, MMSeries : MM series mice. o Sun : Sun mice. The protocol is the same as 'msc' protocol except it used only 3 bytes per packet. o MouseMan, mman : MouseMan protocol. o BusMouse, bm : Non-PS/2 busmice. o LinuxUSB, lnxusb : IMPS2 that doesn't choke on USB (no init attempted). o ps2, PS/2 : PS/2 mice (most non-serial mice use this protocol) o imps2, IMPS/2 : PS/2 IntelliMouse and compatible (not USB, see lnxusb for that.) o mmanps2, MouseManPlusPS/2 : PS/2 Logitech MouseMan+ and compatible. Most of the strings supported by GPM, SVGAlib and XFree can be specified. If you find one that isn't, please report. The special value auto tells input-linux-mouse to read ~/.ggi/input/linux-mouse, and if that fails, $sysconfdir/ggi/input/linux- mouse. If none of the two files are found, input-linux-mouse tries to auto-detect the mouse, and as a last resort uses the mouse information specified in /etc/vga/libvga.config. file The file to read mouse protocol data from; defaults to /dev/mouse. baud Baud rate of mouse device. rts Turns off RTS if set to 0; turns RTS on if set to a number greater than 0. dtr Turns off DTR if set to 0; turns DTR on if set to a number greater than 0. FEATURES
o Generates evPtr* events. FILES
~/.ggi/input/linux-mouse and $sysconfdir/ggi/input/linux-mouse consists of the following entries: mouse mousetype mdev file where mousetype and file has the same semantics as the invocation options of the same names. libgii-1.0.x 2003-08-11 input-linux-mouse(7)