Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: 2 default gateways
Operating Systems AIX 2 default gateways Post 302302608 by kah00na on Tuesday 31st of March 2009 11:59:30 AM
Old 03-31-2009
Like zxmaus, we had this issue too. Cat your /etc/niminfo file and look at the last line that starts with "export ROUTES=". It probably looks something like this:

[CODE]export ROUTES=" default:0:192.168.1.1 ..."[CODE]

Rename the /etc/niminfo file to /etc/niminfo.old and run "smitty nim" on your client machines and go through the setup steps again. Then look at the /etc/niminfo file and see if it looks correct after that.
 

7 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

gateways

I cannot change my gateway. I have five locations (simulated) and i try to ping another of my locations but it says host unreachable and it is showing the gateway as the host i'm pinging withs ip address. I have tried the route command but I couldn't get it to work. Any suggestions on how to... (2 Replies)
Discussion started by: Deuce
2 Replies

2. IP Networking

2 gateways on the same unix box

Hello there: I have these situation : I have a unix sco openserver 5.0.7 box and a windows server 2003. There is a main office and 2 remote office that log in trough a vpn tunnel. One tunnel From Main to remote1 and the other from Main to remote 2. Problem! The dsl connection i have is... (2 Replies)
Discussion started by: josramon
2 Replies

3. AIX

setup of 2 gateways on AIX

Please, anybody help on resolving the following problem? I have 2 netwotks ( 10.0.0.0 and 10.0.11.0 ) on 2 different areas I need both networks to telnet the corresponding ethernet card. This is a prblem because AIX is configured with a default gateway. Please advice how to assign 2... (2 Replies)
Discussion started by: mynikolas
2 Replies

4. Solaris

Configuring 1 Nic card with 2 IP addresses and 2 seperate default Gateways in Solaris

Hi ...... I'm trying to configure my Solaris servers with only one NIC card to have 2 IP addresses as well as 2 different default gateways. ( NOT to be confused with multi-pathing - with 2 physical IPs & 1 virtual ip) Thanks, Remi (1 Reply)
Discussion started by: Remi
1 Replies

5. Shell Programming and Scripting

configuring 2-gateways in linux

Hi, I want to configure 2-gateways in Linux . Please tell me how I can achieve this. I am accesing 2-internet connection through these 2-gateways. So I am looking that if 1-gets down then also other one is working. Regards JAGDISH (1 Reply)
Discussion started by: jagdish.machhi@
1 Replies

6. BSD

Two gateways

I have a web server running FreeBSD 7.2, i have configured two NICs in the following way: fxp0: 200.14.xxx.254 sk0: 200.12.xxx.4 gateway: 200.14.xxx.1 both ip addresses are public but only those requests to fxp0 are successful. I have tried configuring nat and binat in sk0 but it... (4 Replies)
Discussion started by: edgarvm
4 Replies

7. UNIX for Dummies Questions & Answers

iptables / ip route packet routing with multiple gateways

Hi all. Linux noob here. I was hoping someone could help me with configuring some routing rules on my router, an Asus AC68. The router is connected to two gateways, wan0_gateway and wan1_gateway. I have rules set up in the router gui that will push all traffic from every IP other than my own... (0 Replies)
Discussion started by: Bishi
0 Replies
All times are GMT -4. The time now is 03:52 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy