Sponsored Content
Full Discussion: setting up IPMP
Operating Systems Solaris setting up IPMP Post 302301840 by quan0509 on Saturday 28th of March 2009 04:17:46 PM
Old 03-28-2009
you need at least one IP for test purpose. two IPs is not enough for failover.

Regard;

So you can see my example.

I have two Interfaces need to config.

e1000g0
e1000g1
I have 3 IP address for IPMP.

So you can see my information in /etc/hosts

10.151.9.34 fis-srv-center loghost
10.151.9.37 fis-srv-center-e1000g1
10.151.9.36 fis-srv-center-e1000g0

Okie, when you 've done in create hosts file. You need to create two others file.

(1)/etc/hostname.e1000g0 and
(2)/etc/hostname.e1000g1


in file (1) you type .

group ipmp-one up
addif fis-srv-center-e1000g0 deprecated netmask + broadcast + -failover up


in file (2) you type.

fis-srv-center netmask + broadcast + group ipmp-one up
addif fis-srv-center-e1000g1 deprecated netmask + broadcast + -failover up



and IPMP 's working now with failover.




Regards;
 

10 More Discussions You Might Find Interesting

1. Solaris

Ipmp

Hi All, Kindly help me in configuring IPMP or guid me to some link, tried goggling however no luck. Thanks in anticipation (1 Reply)
Discussion started by: kumarmani
1 Replies

2. Solaris

IPMP config

Hi All, I have unplumbed one interface. after that ifconfig -a shows that lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 e1000g0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 ... (7 Replies)
Discussion started by: jegaraman
7 Replies

3. Solaris

IPMP questions

Probe-based IPMP active - active Probe-based IPMP active - passive Link-based only active -standby ???? What are differences between Probe-based IPMP active - passive anddd Link-based only active -standby ???!!! For example in active active probe-based IPMP there are lets... (6 Replies)
Discussion started by: samar
6 Replies

4. Solaris

how to configure IPMP in solaris 9

Hi friends , can anyone provide me the complete steps to configure IPMP in solaris 9 or 10 provided i have two NIC card ? regards jagan (4 Replies)
Discussion started by: jaganblore
4 Replies

5. Solaris

IPMP Configuration

Hi all, Currently i got a server which had two interface. I had study the <SystemAdministration Guide: IP> but still donno what is the correct step to configure it. Can u all help me on it? thanks # ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index... (6 Replies)
Discussion started by: SmartAntz
6 Replies

6. Solaris

IPMP Configuration

Dear All, I have configured IPMP in one of my SUN machine which is having solros 9 version. I have updated all files like /etc/hosts,/etc/hostname.ce0 and /etc/hostname.ce1 and rebooted the server. But IP's are not mounted which i have given in /etc/hosts file. Please find the below ifconfig... (6 Replies)
Discussion started by: lbreddy
6 Replies

7. Solaris

ipmp testing

Please tell me how to configure IPMP in vmware what is the basic working concept of IPMP. please help me (1 Reply)
Discussion started by: sijocg
1 Replies

8. Solaris

IPMP problem

Hi all i had two interface ce0 and ce5 but when i run the ifconfig, it show me alot of extra virtual interface, may i know how to remove it? # ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 ce0:... (2 Replies)
Discussion started by: SmartAntz
2 Replies

9. Solaris

Solaris IPMP

Can any one please explain me the concept behind IPMP in solaris clustering.Basic explanation would be really appreciated... Thanks in Advance vks (2 Replies)
Discussion started by: vks47
2 Replies

10. Solaris

Unable to perform IPMP

Hi, I have perform IPMP on server. but its showing following errors, root@DEVTEST10 # dladm show-dev ce0 link: up speed: 100 Mbps duplex: full ce1 link: up speed: 100 Mbps duplex: full root@DEVTEST10 # root@DEVTEST10 # ifconfig -a lo0: flags=2001000849 mtu 8232 index 1 inet 127.0.0.1... (0 Replies)
Discussion started by: tiger09
0 Replies
if_mpadm(1M)						  System Administration Commands					      if_mpadm(1M)

NAME
if_mpadm - administer interfaces in an IP multipathing group SYNOPSIS
if_mpadm -d | -r ifname DESCRIPTION
The if_mpadm utility administers IP interfaces that are part of an IP Multipathing (IPMP) group. Currently, administration is limited to offlining IP interfaces and undoing previous offline operations. When an IP interface is taken offline, all IP data traffic that was flowing over the IP interface is moved to another IP interface in the IPMP group. In addition, all UP IP addresses hosted on the IP interface are brought down, causing in.mpathd(1M) to stop probe-based failure detection on the IP interface. As a result, an offline IP interface will not be used for any inbound or outbound IP traffic. Only IP inter- faces that are in an IPMP group may be brought offline. If the IP interface is the last functioning interface in the IPMP group, the off- line operation will fail. When an offline operation is undone, any IP addresses hosted on that IP interface are brought UP and will be considered by in.mpathd for probe-based failure detection. In addition, provided the IP interface is otherwise active (see in.mpathd(1M)), it will again be used to send and receive IP data traffic for the IPMP group. Note that not all offline operations can be undone. For instance, in.mpathd may have offlined an IP interface because its hardware address was not unique within its IPMP group. The ipmpstat utility can be used to determine why an IP interface is offline, identify which IP interfaces in a group are being used for inbound and outbound IP traffic, and more; see ipmpstat(1M). OPTIONS
The if_mpadm utility supports the following options: -d ifname Offline the IP interface specified by ifname. If ifname is not in an IPMP group, or the offline would cause the IPMP group to lose network connectivity, the operation will fail. -r ifname Undo a previous offline of the IP interface specified by ifname. If ifname is not offline, the operation will fail. EXAMPLES
Example 1 Offlining an IP Interface The following command offlines the IP interface under0, causing any IP packets that were being sent and received through it to be handled by another IP interface in its group. example% if_mpadm -d under0 Example 2 Undoing a Previous Offline Operation Use the following command to undo the operation in the previous example: example% if_mpdadm -r under0 ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ |Interface Stability |Unstable | +-----------------------------+-----------------------------+ SEE ALSO
ifconfig(1M), in.mpathd(1M), ipmpstat(1M), attributes(5) DIAGNOSTICS
cannot offline: no other functioning interfaces are in its IPMP group. Description: This message means that offlining the IP interface would leave the IPMP group without network connectivity. cannot offline: not a physical interface or not in an IPMP group Description: This means that the IP interface is not an underlying interface in an IPMP group, and therefore is not eligible to be offlined. SunOS 5.11 5 Jan 2009 if_mpadm(1M)
All times are GMT -4. The time now is 10:33 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy