Sponsored Content
Full Discussion: Not able to ping
Operating Systems Linux Not able to ping Post 302299971 by TonyFullerMalv on Sunday 22nd of March 2009 05:22:43 PM
Old 03-22-2009
Perhaps one end or the other has a firewall set up to block ping requests?

Try running:

Code:
$ sudo iptables --list

On each end to see if any firewall rules have been set up?

Last edited by reborg; 03-22-2009 at 09:35 PM.. Reason: insert missing "other"
 

10 More Discussions You Might Find Interesting

1. IP Networking

About Ping

Hi, When I pinged a machin, I got to be seen a different kind of reply from that machine. This is as below : "Reply from 136.128.11.116: Source quench received." Which I felt like an un-usual message. So what does this mean. Regards & Thanks in advance. Vishwa. (4 Replies)
Discussion started by: S.Vishwanath
4 Replies

2. UNIX for Dummies Questions & Answers

ping

Hi there hope list can help I'm looking for a command that does the following lets say i ping a server 00.00.000.00 and this server is up and running how do i get the ping command to return a UP or a Down meaning if the command is true do this if the command is False do this ... (2 Replies)
Discussion started by: nemex
2 Replies

3. AIX

ping

We can ping out but the return never comes back even to localhost ping localhost PING loopback: (127.0.0.1): 56 data bytes 64 bytes from 127.0.0.1: icmp_seq=0 ttl=255 time=0 ms it just sits there.... any ideas, any files to check (1 Reply)
Discussion started by: csaunders
1 Replies

4. UNIX for Dummies Questions & Answers

Ping

Hi , I have one system installed on Linux Red Hat 3.0. I have ip of system 3.156.168.*** and i want to ping some port that is on this IP which command i can do this? sam70 (1 Reply)
Discussion started by: sam70
1 Replies

5. IP Networking

can't ping by ip

hi, I m trying to ping ip on the network . The machine is started but i can't access and can't ping it .. But when i restarts that machine that works fine..... can anybody have an idea about this problem ?? if then reply .. thanks (2 Replies)
Discussion started by: tahir23
2 Replies

6. IP Networking

Can't Ping

I have an old MP-Ras Unix system. I have setup netowkring but am unable to ping any local network pcs or the default gateway. If i use the arp -a command I receive the correct mac address for all connected pcs but I cannot ping anything except the local address. Any help would be appreciative. ... (7 Replies)
Discussion started by: Rutgerncas
7 Replies

7. Shell Programming and Scripting

Animation Ping on Solaris Like Cisco Ping

Hi, I develop simple animation ping script on Solaris Platform. It is like Cisco ping. Examples and source code are below. bash-3.00$ gokcell 152.155.180.8 30 Sending 30 Ping Packets to 152.155.180.8 !!!!!!!!!!!!!.!!!!!!!!!!!!!!!. % 93.33 success... % 6.66 packet loss...... (1 Reply)
Discussion started by: gokcell
1 Replies

8. IP Networking

PING

I am unable to ping my remote server.My server is unable to ping the same. both are able to ping the gateway. both the ip's are on same network.i use a proxy tunnel on my remote server.Help if any clues. (6 Replies)
Discussion started by: oslbhavana
6 Replies

9. Shell Programming and Scripting

How to get reason for ping failure using perls Net::Ping->new("icmp");?

Hi I am using perl to ping a list of nodes - with script below : $p = Net::Ping->new("icmp"); if ($p->ping($host,1)){ print "$host is alive.\n"; } else { print "$host is unreacheable.\n"; } $p->close();... (4 Replies)
Discussion started by: tavanagh
4 Replies

10. Programming

Ping test sends mail when ping fails

help with bash script! im am working on this script to make sure my server will stay online, so i made this script.. HOSTS="192.168.138.155" COUNT=4 pingtest(){ for myhost in "$@" do ping -c "$COUNT" "$myhost" &&return 1 done return 0 } if pingtest $HOSTS #100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies
APF(1)							      General Commands Manual							    APF(1)

NAME
apf - easy iptables based firewall system SYNOPSIS
apf DESCRIPTION
This manual page documents briefly the apf command. This manual page was written for the Debian distribution because the original program does not have a manual page. Advanced Policy Firewall (APF) is an iptables (netfilter) based firewall system designed around the essential needs of today's Internet deployed servers and the unique needs of custom deployed Linux installations. The configuration of APF is designed to be very informative and present the user with an easy to follow process, from top to bottom of the configuration file. The management of APF on a day-to-day basis is conducted from the command line with the 'apf' command, which includes detailed usage information and all the features one would expect from a current and forward thinking firewall solution. OPTIONS
apf follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is included below. -s|--start load all firewall rules -r|--restart stop (flush) & reload firewall rules -l|--list list all firewall rules -t|--status output firewall status log -e|--refresh refresh & resolve dns names in trust rules -a <HOST CMT|--allow <HOST COMMENT> add host (IP/FQDN) to allow_hosts.rules and immediately load new rule into firewall -d <HOST CMT|--deny <HOST COMMENT> add host (IP/FQDN) to deny_hosts.rules and immediately load new rule into firewall -u <HOST>|--remove <HOST> remove host from [glob]*_hosts.rules and immediately remove rule from firewall -o|--ovars output all configuration options COPYRIGHT
Copyright (C) 1999-2007, R-fx Networks <proj@r-fx.org> Copyright (C) 2007, Ryan MacDonald <ryan@r-fx.org> This program may be freely redistributed under the terms of the GNU GPL This manual page was written by Giuseppe Iuculano <giuseppe@iuculano.it>, for the Debian project (but may be used by others). August 17, 2008 APF(1)
All times are GMT -4. The time now is 09:53 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy