Sponsored Content
Operating Systems Solaris T5240 and Internal SAS RAID Configuration help Post 302299757 by nicktrix on Saturday 21st of March 2009 07:15:44 AM
Old 03-21-2009
Thanks DukeNuke2... I will use that bootable cd and inform if I face any difficulty.. I have found that bootable live cd from the given link... It's latest I think....

Download Search Results
 

10 More Discussions You Might Find Interesting

1. AIX

regd raid 0 configuration

Hey Alll Thanks for the help u give me yesterday,i need a help again from u all guys i have RS 6000 server with AIX 4.3.3 OS and with external storage (multipack) with 12 Hard disk drive which will be connected to RS 6000 scsi controller ,i dont have any raid card. now i have to... (0 Replies)
Discussion started by: solaris8in
0 Replies

2. SCO

driver needed for hp smartarry p200i sas raid controller

recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
Discussion started by: prakrithi
3 Replies

3. Solaris

istall sas raid HBA internal card

I need to install a raid HBA internal card on a T5240. The reason is I have more drives and the current mother board controller does not support more than 4 drives. My question is I have raidctl set up on current drives. If I install new HBA card do I have to delete current raidctl and... (3 Replies)
Discussion started by: photon
3 Replies

4. Solaris

Install Solaris 10 with an internal StorageTek SAS HBA Raid card

Hi all i would like to ask some suggests about my next job! I have to install a new Sun Netra T5220, with an additional internal StorageTek SAS HBA Raid. The problem come in if every disk is now controlled by the HBA, how can I install the OS? No disk is being detected by the OS. SAS card... (2 Replies)
Discussion started by: kakabobo
2 Replies

5. Solaris

installing solaris with StorageTek SAS RAID Internal HBA

i was given a task which needs to perform a raid 1 on the boot disk, and 4 other disks on raid 10. Is there any other alternative in installing solaris 10 other than through network installation?will be using solaris update 6. while reading through the user guide i got pretty confuse. ... (1 Reply)
Discussion started by: monstar1407
1 Replies

6. Red Hat

Software RAID configuration

We have configured software based RAID5 with LVM on our RHEL5 servers. Please let us know if its good to configure software RAID on live environment servers. What can be the disadvantages of software RAID against hardware RAID (4 Replies)
Discussion started by: mitchnelson
4 Replies

7. AIX

Internal PCI X RAID Controller issue ?

Hello folks, Could someone tell me why I unable to create pdisks for a RAID Array # lscfg | grep scsi + sisscsia0 U787A.001.DPM0707-P1 PCI-X Dual Channel Ultra320 SCSI Adapter + scsi0 U787A.001.DPM0707-P1-T10 PCI-X Dual Channel Ultra320 SCSI Adapter... (12 Replies)
Discussion started by: filosophizer
12 Replies

8. Solaris

Cannot configure RAID on T5240

Hi ! I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before. I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl. ... (2 Replies)
Discussion started by: delavega
2 Replies

9. Red Hat

RAID Configuration for IBM Serveraid-7k SCSI RAID Controller

Hello, I want to delete a RAID configuration an old server has. Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton? I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies

10. AIX

Replaced pdisk not showing up in SAS Disk Array Configuration

OSLevel: 5300-10-02-0943 System Model: IBM,8203-E4A Power 6 == Hi! I replaced a failed pdisk in the raid enclosure as follows, - rmdev -l 'pdisk18' '-d' - Replaced it. - cfgmgr (detected) - I can see the new drive, with the correct serial # lscfg -v -l pdisk18 pdisk18... (2 Replies)
Discussion started by: estrar
2 Replies
TWS(4)							   BSD Kernel Interfaces Manual 						    TWS(4)

NAME
tws -- 3ware 9750 SATA+SAS 6Gb/s RAID controller card driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device scbus device tws Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): tws_load="YES" DESCRIPTION
The tws driver provides support for LSI's 3ware 9750 SATA+SAS 6Gb/s RAID controller cards. These controllers feature the LSISAS2108 6Gb/s SAS RAID-on-Chip (ROC) and are available in 4- and 8-port configurations, supports RAID levels 0, 1, 5, 6, 10, 50 and single disk, with 96 SATA and/or SAS hard drives and SSDs. For further hardware information, see http://www.lsi.com/. HARDWARE
The tws driver supports the following SATA/SAS RAID controller: o LSI's 3ware SAS 9750 series LOADER TUNABLES
Tunables can be set at the loader(8) prompt before booting the kernel or stored in loader.conf(5). hw.tws.cam_depth The maximum queued CAM SIM requests for one controller. The default value is 256. hw.tws.enable_msi This tunable enables MSI support on the controller if set to a non-zero value. The default value is 0. hw.tws.queue_depth The maximum queued requests for one controller. hw.tws.use_32bit_sgls Limit the driver to use only 32-bit SG elements regardless whether the operating system is running in 64-bit mode. The default value is 0. FILES
/dev/da? array/logical disk interface /dev/tws? management interface DIAGNOSTICS
Whenever the driver encounters a command failure, it prints out an error code in the format: "ERROR: (<error source>: <error code>):", fol- lowed by a text description of the error. There are other error messages and warnings that the driver prints out, depending on the kinds of errors that it encounters. If the driver is compiled with TWS_DEBUG defined, it prints out a whole bunch of debug messages. SEE ALSO
da(4), scsi(4) AUTHORS
The tws driver was written by Manjunath Ranganathaiah for LSI and this manual page was written by Xin LI <delphij@FreeBSD.org> for iXsystems, Inc. BSD
October 4, 2011 BSD
All times are GMT -4. The time now is 03:00 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy