I am not into Solaris but I know it from my Debian box. Maybe it helps so here you go:
I just had to make sure the USB kernel modules / drivers are there and then I just mount it to some mountpoint. It is not like that when I plug in the stick that there will be automatically be a device file created unter /dev. The needed device files are already there.
I just go on with
When plugged in, I get in /proc/bus/usb/devices following additional entry:
The other entries are about the controller etc.
Make sure that sda1 is not a partition or something of your other SCSI devices.
Hi...
question is this:
How do I mount an LVD hotswap scsi drive in bay #2 on a netra using the mount command? volmgt doesn't seem to mount it and/or I don't know how to view the drives data if it's formatted which it may not be. This drive is not new out of the box so I'm not sure.
... (4 Replies)
I am using Redhat 9 Linux, and am trying to get my external usb drive mounted (fat32). If I look at the KDE Control panel, it lists a usb 2.0 storage device under "USB Devices" (also in /proc/bus/usb), and under "SCSI" as scsi1. I looked at /proc/scsi/usb-storage-0, and it lists it there also. What... (6 Replies)
Dear All
Last day in Aix 5.2 server by executing
# df –g
I found following:
Filesystem GB blocks Free %Used Iused %Iused Mounted on
.
.
/dev/fslv00 58.00 136.70 -135% 212103 1% /sprod
After shutting down by following command
# shutdown –h
And when... (1 Reply)
Hi!
I have a problem with my disk, it is full as you can see
# df
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/sda1 64380356 63125180 0 100% /
none 3116000 0 3116000 0% /dev/shm
/dev/sdb1 282015652... (10 Replies)
Hello Gurus!!
Very recently i tried to mount a USB pen drive onto my solaris 10 (X4170 model) server. As i understand, in ideal scenarios it should get mounted automatically, but it did not happen. Neither anything is shown in "iostat -En" output or "rmformat -l" about the pen drive.
I also... (10 Replies)
Hi,
I am facing issue with one of the drive is solaris 10. it is showing offline in the messages file
scsi: WARNING: /pci@2,600000/QLGC,qlc@0/fp@0,0/ssd@w5006016746e00b1b,0 (ssd0):
drive offline
genunix: WARNING: Page83 data not standards compliant DGC LUNZ 0430
... (1 Reply)
I have a Sun-Fire V440 running with Solaris 9 and am trying to get a WD USB Hard Drive mounted. None of the articles I've read so far have helped.
Output from rmformat:
Looking for devices...
1. Volmgt Node: /vol/dev/aliases/rmdisk0
Logical Node: /dev/rdsk/c5t0d0s2
... (17 Replies)
Discussion started by: oldtimertj
17 Replies
LEARN ABOUT MINIX
mount_pcfs
mount_pcfs(1M) System Administration Commands mount_pcfs(1M)NAME
mount_pcfs - mount pcfs file systems
SYNOPSIS
mount -F pcfs [generic_options] [-o FSType-specific_options] special | mount_point
mount -F pcfs [generic_options] [-o FSType-specific_options] special mount_point
DESCRIPTION
mount attaches an MS-DOS file system (pcfs) to the file system hierarchy at the mount_point, which is the pathname of a directory. If
mount_point has any contents prior to the mount operation, these are hidden until the file system is unmounted.
If mount is invoked with special or mount_point as the only arguments, mount will search /etc/vfstab to fill in the missing arguments,
including the FSType-specific_options; see mount(1M) for more details.
The special argument can be one of two special device file types:
o A floppy disk, such as /dev/diskette0 or /dev/diskette1.
o A DOS logical drive on a hard disk expressed as device-name:logical-drive , where device-name specifies the special block device-file
for the whole disk and logical-drive is either a drive letter (c through z) or a drive number (1 through 24). Examples are
/dev/dsk/c0t0d0p0:c and /dev/dsk/c0t0d0p0:1.
The special device file type must have a formatted MS-DOS file system with either a 12-bit, 16-bit, or 32-bit File Allocation Table.
OPTIONS
generic_options
See mount(1M) for the list of supported options.
-o
Specify pcfs file system specific options. The following options are supported:
foldcase|nofoldcase
Force uppercase characters in filenames to lowercase when reading them from the filesystem. This is for compatibility with the pre-
vious behavior of pcfs. The default is nofoldcase.
FILES
/etc/mnttab table of mounted file systems
/etc/vfstab list of default parameters for each file system
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWesu |
+-----------------------------+-----------------------------+
SEE ALSO mount(1M), mountall(1M), mount(2), mnttab(4), vfstab(4), attributes(5), pcfs(7FS)NOTES
If the directory on which a file system is to be mounted is a symbolic link, the file system is mounted on the directory to which the sym-
bolic link refers, rather than on top of the symbolic link itself.
SunOS 5.10 24 Nov 2003 mount_pcfs(1M)