I am not into Solaris but I know it from my Debian box. Maybe it helps so here you go:
I just had to make sure the USB kernel modules / drivers are there and then I just mount it to some mountpoint. It is not like that when I plug in the stick that there will be automatically be a device file created unter /dev. The needed device files are already there.
I just go on with
When plugged in, I get in /proc/bus/usb/devices following additional entry:
The other entries are about the controller etc.
Make sure that sda1 is not a partition or something of your other SCSI devices.
Hi...
question is this:
How do I mount an LVD hotswap scsi drive in bay #2 on a netra using the mount command? volmgt doesn't seem to mount it and/or I don't know how to view the drives data if it's formatted which it may not be. This drive is not new out of the box so I'm not sure.
... (4 Replies)
I am using Redhat 9 Linux, and am trying to get my external usb drive mounted (fat32). If I look at the KDE Control panel, it lists a usb 2.0 storage device under "USB Devices" (also in /proc/bus/usb), and under "SCSI" as scsi1. I looked at /proc/scsi/usb-storage-0, and it lists it there also. What... (6 Replies)
Dear All
Last day in Aix 5.2 server by executing
# df –g
I found following:
Filesystem GB blocks Free %Used Iused %Iused Mounted on
.
.
/dev/fslv00 58.00 136.70 -135% 212103 1% /sprod
After shutting down by following command
# shutdown –h
And when... (1 Reply)
Hi!
I have a problem with my disk, it is full as you can see
# df
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/sda1 64380356 63125180 0 100% /
none 3116000 0 3116000 0% /dev/shm
/dev/sdb1 282015652... (10 Replies)
Hello Gurus!!
Very recently i tried to mount a USB pen drive onto my solaris 10 (X4170 model) server. As i understand, in ideal scenarios it should get mounted automatically, but it did not happen. Neither anything is shown in "iostat -En" output or "rmformat -l" about the pen drive.
I also... (10 Replies)
Hi,
I am facing issue with one of the drive is solaris 10. it is showing offline in the messages file
scsi: WARNING: /pci@2,600000/QLGC,qlc@0/fp@0,0/ssd@w5006016746e00b1b,0 (ssd0):
drive offline
genunix: WARNING: Page83 data not standards compliant DGC LUNZ 0430
... (1 Reply)
I have a Sun-Fire V440 running with Solaris 9 and am trying to get a WD USB Hard Drive mounted. None of the articles I've read so far have helped.
Output from rmformat:
Looking for devices...
1. Volmgt Node: /vol/dev/aliases/rmdisk0
Logical Node: /dev/rdsk/c5t0d0s2
... (17 Replies)
Discussion started by: oldtimertj
17 Replies
LEARN ABOUT DEBIAN
usb-devices
usb-devices(1) Linux USB Utilities usb-devices(1)NAME
usb-devices - print USB device details
SYNOPSIS
usb-devices
DESCRIPTION
usb-devices is a (bash) shell script that can be used to display details of USB buses in the system and the devices connected to them.
The output of the script is similar to the usb/devices file available either under /proc/bus (if usbfs is mounted), or under /sys/ker-
nel/debug (if debugfs is mounted there). The script is primarily intended to be used if the file is not available.
In contrast to the usb/devices file, this script only lists active interfaces (those marked with a "*" in the usb/devices file) and their
endpoints.
Be advised that there can be differences in the way information is sorted, as well as in the format of the output.
RETURN VALUE
If sysfs is not mounted, a non-zero exit code is returned.
FILES
/sys/bus/usb/devices/usb*
The part of the sysfs tree the script walks through to assemble the printed information.
/proc/bus/usb/devices
Location where the usb/devices file can normally be found for Linux kernels before 2.6.31, if usbfs is mounted.
/sys/kernel/debug/usb/devices
Location where the usb/devices file can normally be found for Linux kernel 2.6.31 and later, if debugfs is mounted.
SEE ALSO lsusb(8), usbview(8).
AUTHORS
Greg Kroah-Hartman <greg@kroah.com>
Randy Dunlap <rdunlap@xenotime.net>
Frans Pop <elendil@planet.nl>
usbutils-005 23 June 2009 usb-devices(1)