03-19-2009
I can't recall the reason but I stopped using the 905B at some point and only install the 905-TX version, which has given good service. Or an earlier PCI based one, can't remember the type, and when all else fails I fall back to the 509 and the ISA bus.
You might try running the DOS based diagnostics and see if anything shows up but based on the multiple failures on that card I suspect that you would be better off getting the TX version.
What kind of system are you dealing with, hardware wise? Most of mine is PII based but I may have some PIII.
10 More Discussions You Might Find Interesting
1. SCO
Happy new year guys.
I have a inspiron 5100 laptop "Dell"
When i'm trying to install SCO openserver 5.0.7 i get this error right after it goes thru the hardware bootup stage.
The error is (PANIC: wdsetparam: no device info for ctlr 1 drive 0
is ctlr 0 , drive 0 not... (0 Replies)
Discussion started by: josramon
0 Replies
2. Windows & DOS: Issues & Discussions
Hello guys , i have a big big problem.
At the company that i work for there are like 4 pcs that are sending and recieving a lot of packets to the point that the network is down.
we think that it might be a virus, we run all the antivirus that you could posible think of and nothing so far.
... (2 Replies)
Discussion started by: josramon
2 Replies
3. SuSE
Hullo everyone,
I have recently installed SUSE 9.1 and attached it to my Network router (Actiontec 54Mbps Wireless DSL Gateway) but can't connect to the internet. It comes up with the following error message:
An error occurred while loading "http://www.yahoo.com":Timeout on server - connection... (2 Replies)
Discussion started by: sybella1
2 Replies
4. SCO
I have several printers setup but nothing prints.
I get the following error email
Subject: Status of lp request aclj3-2297
Your request aclj3-2297 destined for aclj3
encountered an error while printing on printer aclj3.
Reason for failure:
cat: cannot open 0: No such file or... (1 Reply)
Discussion started by: Jessie Nand
1 Replies
5. Post Here to Contact Site Administrators and Moderators
I am installing a HP printer using ./hpnpcfg and I am getting the following:
Please enter selection: 5
Enter the network peripheral name or IP address: hpndlife
The following types of test files can be sent to the printer:
1) text file
... (0 Replies)
Discussion started by: Likando Luywa
0 Replies
6. Slackware
I recently installed slackware 11 and have been very happy with it until I found out that some gnome related apps can cause gnome's network manager to alter the rc.init1 script by adding 3 lines to the script containing only the command, eth_up. This causes the script not to run properly and not... (1 Reply)
Discussion started by: djtrippin
1 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I've got a really old system we use for call logging. The OS is SCO 3.2
uname -a output
SCO_SV bts7053 3.2 2 i386
the problem we are having is that its no longer doing its backups. The original problem was the tape drive, which has been replaced twice now. Because the company are... (1 Reply)
Discussion started by: johno12345
1 Replies
8. Solaris
Hey. i have a SPARCstation 5 running solaris 8 and CDE,
i know this hardware is really old but its the only Solaris machine i can afford at this time, (Student) but im having a hard time getting it on the internet, im using a cable modem, andt DHCP IPv4, but i can`t get a connection, i have heard... (0 Replies)
Discussion started by: mads-nielsen
0 Replies
9. SCO
hello, i am new to unix and need support</SPAN></SPAN>
</SPAN></SPAN>The problem is:
I have a SCO 5.0.5 server, and has no local network access, I think my problem are the drivers for network card.
my network card is Kingston EtheRx PCI Fast Ethernet Adapter KNE120TX and already installed the... (9 Replies)
Discussion started by: daniel_cie
9 Replies
10. Shell Programming and Scripting
Hi,
I work on several Sun servers running Solaris (SunOS 5.10). All of these are Application Servers with a propietary software running on it.
It happens that some times (not regularly/deterministic and not so often, i.e. twice a month circa) we register what I think are network problems.
I say... (4 Replies)
Discussion started by: Evan
4 Replies
SET_NET_DEFAULT(8) System Manager's Manual SET_NET_DEFAULT(8)
NAME
s_n_d, set_net_default - select the default TCP/IP network
SYNOPSIS
set_net_default: not found
DESCRIPTION
This manual page is here because so many others refer to it. The set_net_default command does not exist under standard Minix, because the
TCP/IP server only supports one network. The server under Minix-vmd supports four different networks, that can each be chosen as the
default network.
The TCP/IP library and commands do have a notion about a "default network" however, because the code is shared between the Minix versions.
So if you want to venture into network programming then you should know about the devices and environment variables mentioned below to make
your program compatible. (Especially since there is a plan to upgrade the TCP/IP server for standard Minix.)
Options and environment to change the default
Many TCP/IP programs implement the following options and environment variables to change the default devices set by set_net_default. The
options are only implemented for low level programs where it makes sense to name a network device. The environment variables are used in
all code. You can run a process and all its children connected to a different network by setting four environment variables.
ETH_DEVICE=device
-E device
Device to use as raw ethernet device instead of the default /dev/eth.
PSIP_DEVICE=device
-P device
Pseudo IP device to use instead of /dev/psip.
IP_DEVICE=device
-I device
IP device to use instead of /dev/ip.
TCP_DEVICE=device
-T device
TCP device to use.
UDP_DEVICE=device
-U device
UDP device to use.
FILES
/dev/eth[01] First and second raw ethernet.
/dev/psip[01] First and second Pseudo IP network.
/dev/ip[0123] IP devices for two ethernets and two Pseudo IP networks.
/dev/tcp[0123] TCP devices for same four networks.
/dev/udp[0123] UDP devices.
/dev/eth, /dev/psip, /dev/ip, /dev/tcp, /dev/udp
Devices for the default network, links to the devices above. Eth is only present if ethernet is the default, psip only
for pseudo IP.
SEE ALSO
ip(4), boot(8).
AUTHOR
Kees J. Bot (kjb@cs.vu.nl)
SET_NET_DEFAULT(8)