Sponsored Content
Full Discussion: network problems with sco
Operating Systems SCO network problems with sco Post 302299053 by edfair on Thursday 19th of March 2009 04:53:04 AM
Old 03-19-2009
I can't recall the reason but I stopped using the 905B at some point and only install the 905-TX version, which has given good service. Or an earlier PCI based one, can't remember the type, and when all else fails I fall back to the 509 and the ISA bus.

You might try running the DOS based diagnostics and see if anything shows up but based on the multiple failures on that card I suspect that you would be better off getting the TX version.

What kind of system are you dealing with, hardware wise? Most of mine is PII based but I may have some PIII.
 

10 More Discussions You Might Find Interesting

1. SCO

SCO 5.0.7 Installation Problems

Happy new year guys. I have a inspiron 5100 laptop "Dell" When i'm trying to install SCO openserver 5.0.7 i get this error right after it goes thru the hardware bootup stage. The error is (PANIC: wdsetparam: no device info for ctlr 1 drive 0 is ctlr 0 , drive 0 not... (0 Replies)
Discussion started by: josramon
0 Replies

2. Windows & DOS: Issues & Discussions

Windows xp network problems

Hello guys , i have a big big problem. At the company that i work for there are like 4 pcs that are sending and recieving a lot of packets to the point that the network is down. we think that it might be a virus, we run all the antivirus that you could posible think of and nothing so far. ... (2 Replies)
Discussion started by: josramon
2 Replies

3. SuSE

Linux Network problems-Please help

Hullo everyone, I have recently installed SUSE 9.1 and attached it to my Network router (Actiontec 54Mbps Wireless DSL Gateway) but can't connect to the internet. It comes up with the following error message: An error occurred while loading "http://www.yahoo.com":Timeout on server - connection... (2 Replies)
Discussion started by: sybella1
2 Replies

4. SCO

Printing Problems with SCO 5.0

I have several printers setup but nothing prints. I get the following error email Subject: Status of lp request aclj3-2297 Your request aclj3-2297 destined for aclj3 encountered an error while printing on printer aclj3. Reason for failure: cat: cannot open 0: No such file or... (1 Reply)
Discussion started by: Jessie Nand
1 Replies

5. Post Here to Contact Site Administrators and Moderators

Sco Network Printing

I am installing a HP printer using ./hpnpcfg and I am getting the following: Please enter selection: 5 Enter the network peripheral name or IP address: hpndlife The following types of test files can be sent to the printer: 1) text file ... (0 Replies)
Discussion started by: Likando Luywa
0 Replies

6. Slackware

Network Startup Problems

I recently installed slackware 11 and have been very happy with it until I found out that some gnome related apps can cause gnome's network manager to alter the rc.init1 script by adding 3 lines to the script containing only the command, eth_up. This causes the script not to run properly and not... (1 Reply)
Discussion started by: djtrippin
1 Replies

7. UNIX for Dummies Questions & Answers

SCO NFS problems

Hi, I've got a really old system we use for call logging. The OS is SCO 3.2 uname -a output SCO_SV bts7053 3.2 2 i386 the problem we are having is that its no longer doing its backups. The original problem was the tape drive, which has been replaced twice now. Because the company are... (1 Reply)
Discussion started by: johno12345
1 Replies

8. Solaris

Problems with SS5 Network

Hey. i have a SPARCstation 5 running solaris 8 and CDE, i know this hardware is really old but its the only Solaris machine i can afford at this time, (Student) but im having a hard time getting it on the internet, im using a cable modem, andt DHCP IPv4, but i can`t get a connection, i have heard... (0 Replies)
Discussion started by: mads-nielsen
0 Replies

9. SCO

Problems with network card in SCO

hello, i am new to unix and need support</SPAN></SPAN> </SPAN></SPAN>The problem is: I have a SCO 5.0.5 server, and has no local network access, I think my problem are the drivers for network card. my network card is Kingston EtheRx PCI Fast Ethernet Adapter KNE120TX and already installed the... (9 Replies)
Discussion started by: daniel_cie
9 Replies

10. Shell Programming and Scripting

How to demonstrate network problems?

Hi, I work on several Sun servers running Solaris (SunOS 5.10). All of these are Application Servers with a propietary software running on it. It happens that some times (not regularly/deterministic and not so often, i.e. twice a month circa) we register what I think are network problems. I say... (4 Replies)
Discussion started by: Evan
4 Replies
DEVICE(9)						   BSD Kernel Developer's Manual						 DEVICE(9)

NAME
device -- an abstract representation of a device SYNOPSIS
typedef struct device *device_t; DESCRIPTION
The device object represents a piece of hardware attached to the system such as an expansion card, the bus which that card is plugged into, disk drives attached to the expansion card etc. The system defines one device, root_bus and all other devices are created dynamically during autoconfiguration. Normally devices representing top-level busses in the system (ISA, PCI etc.) will be attached directly to root_bus and other devices will be added as children of their relevant bus. The devices in a system form a tree. All devices except root_bus have a parent (see device_get_parent(9)). In addition, any device can have children attached to it (see device_add_child(9), device_add_child_ordered(9), device_find_child(9), device_get_children(9), and device_delete_child(9)). A device which has been successfully probed and attached to the system will also have a driver (see device_get_driver(9) and driver(9)) and a devclass (see device_get_devclass(9) and devclass(9)). Various other attributes of the device include a unit number (see device_get_unit(9)), verbose description (normally supplied by the driver, see device_set_desc(9) and device_get_desc(9)), a set of bus-spe- cific variables (see device_get_ivars(9)) and a set of driver-specific variables (see device_get_softc(9)). Devices can be in one of several states: DS_NOTPRESENT the device has not been probed for existence or the probe failed DS_ALIVE the device probe succeeded but not yet attached DS_ATTACHED the device has been successfully attached DS_BUSY the device is currently open The current state of the device can be determined by calling device_get_state(9). SEE ALSO
devclass(9), driver(9) AUTHORS
This manual page was written by Doug Rabson. BSD
June 16, 1998 BSD
All times are GMT -4. The time now is 12:42 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy