03-17-2009
dbell37
Thanks a lot for your answer. Actually, I've already solved this problem - I discussed it on Sun forums and I was told to update firmware, but when performing this procedure I faced with some errors... Anyway, thanks for answer
![Wink Smilie](https://www.unix.com/images/smilies/wink.gif)
8 More Discussions You Might Find Interesting
1. Solaris
I have a Sun Sparc T2000 (Solaris 10 05-08) and have installed a PCI-X 4GB Single Port HBA card in it.
I have one StorageTek 2540 array that I would like to connect to the T2000.
For the moment it would be a single path connection, but I've ordered a 2nd HBA, so eventually it would be... (4 Replies)
Discussion started by: soliberus
4 Replies
2. Solaris
Hi!
I have Sun StorageTek 2540 FC array and CAM works very slowly - I can wait for software response even more than 2 minutes... I run this software on Windows machine with Firefox Web Browser but speed is terrible... How can I make it works at least a little bit faster?.. (2 Replies)
Discussion started by: Sapfeer
2 Replies
3. Solaris
Hi,
I have a simple question on how to correctly disable the matrix?
Looking for the Common Array Manager and I do not see this option...
Thank for help (3 Replies)
Discussion started by: bieszczaders
3 Replies
4. Solaris
Hi peeps,
Was wondering if anyone can help me, got a couple of storagetek 2540's that I need to configure. Trouble is I think they were brought as second user as all that came with them was cables.
Does anyone know how to configure them (i.e. create raid sets and map to Luns and present... (1 Reply)
Discussion started by: callmebob
1 Replies
5. Hardware
Hello all !
I am a beginner about system and networking , and after some research on internet , i didn't find any relevant information , so i post here , if someone have an experience with this kind of material or if some documentation about how to connect my storage device on my server.
I... (2 Replies)
Discussion started by: acorradi
2 Replies
6. Filesystems, Disks and Memory
Hi,
I have a question about Sun StorageTek Common Array Manager (CAM): What is the concept of 'host'? Is it the hostname of the server that has access to the managed array? If so, can I use its IP instead of its hostname?
I've found a 'host' under CAM called XYZ (See below). In our... (7 Replies)
Discussion started by: aixlover
7 Replies
7. Hardware
Hi Guys and Gals,
Wionder if you could help me, got a problem with a controller on a storagetek 2540, dead when fully powered up but if you reboot, it is ok for a couple of seconds (and you can ping it). Then once the array is fully up, it goes faulty and is un-pingable.
Had anyone... (4 Replies)
Discussion started by: callmebob
4 Replies
8. Solaris
Bought a Sun StorageTek 2540 SAN array a few years ago from a company that was going out of business. When we first set it up, we were able to get all the software (Common Array Manager) and firmware directly from Sun.
We just upgraded the drives, but the array is too large for the firmware. Now... (6 Replies)
Discussion started by: edison303
6 Replies
RARPD(8) System Manager's Manual RARPD(8)
NAME
rarpd - reverse address resolution protocol daemon
SYNOPSIS
rarpd [-v] [-i interface ]
DESCRIPTION
Rarpd listens on the ethernet for broadcast packets asking for reverse address resolution. These packets are sent by hosts at boot time to
find out their IP address. Rarpd looks up the six octet ethernet number in the ethers map finding a host name. This name is translated to
the IP address of the host by a DNS lookup. The IP address is then sent to the host.
Before rarpd can start its service it first finds out what the IP address and hardware address of the ethernet is.
Warning! Sun diskless workstations assume that the first RARP server that answers is the host they are to boot from. For this to work all
other Sun RARP servers delay their answer if they are not also the requestors boot server. This rarpd does not have this kludge so it will
happily engage the Sun boot server to see who can answer the client first. Unless your host can actually serve a Sun diskless client, it
is better not to list any more hosts in the ethers file than necessary.
OPTIONS
-v Be verbose. Show requests which the daemon is responding to.
-i Bind to the named interface. By default rarpd binds to the default interface for the local system type, if available.
SEE ALSO
ifconfig(8), ethers(5), hosts(5),
AUTHOR
Derrick J. Brashear (shadow@dementia.org)
The man page is mostly from the Minix version, by Kees J. Bot (kjb@cs.vu.nl)
RARPD(8)