03-16-2009
the thread is over 7 years old O_o
so i hope the OP has found the needed answer. i'll close this one down for now.
9 More Discussions You Might Find Interesting
1. Solaris
hai everybody n good morning........here r some queries.......
1. what is the interlace value in RAID 0 (striping.......)
2. How many no of metadevices are required for mirroring and why......... (1 Reply)
Discussion started by: sudhansu
1 Replies
2. Solaris
hi all...sudhansu here............ i need some help..........
what is RAID 0+1 and RAID 1+0.............what is the difference between them................
suppose i have 80 gb disk space,then which RAID level i follow n why......... i need redundancy n maximum storage..........please help (3 Replies)
Discussion started by: sudhansu
3 Replies
3. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
4. Solaris
Dear ALl,
I have a RAID 5 volume which is as below
d120 r 60GB c1t2d0s5 c1t3d0s5 c1t4d0s5 c1t5d0s5
d7 r 99GB c1t2d0s0 c1t3d0s0 c1t4d0s0 c1t5d0s0
d110 r 99GB c1t2d0s4 c1t3d0s4 c1t4d0s4 c1t5d0s4
d8 r 99GB c1t2d0s1 c1t3d0s1... (2 Replies)
Discussion started by: jegaraman
2 Replies
5. Solaris
Hello All,
I have read enough of texts on Raid 01 and Raid 10 on solaris :wall: . But no-where found a way to create them using SVM. Some one pls tell me how to do or Post some link if that helps.
TIA
Curious
solarister (1 Reply)
Discussion started by: Solarister
1 Replies
6. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
7. UNIX for Dummies Questions & Answers
Hi Gurus,
Can any one explain me the difference between hardware RAID and s/w RAID.
Thanks in Advance. (1 Reply)
Discussion started by: rama krishna
1 Replies
8. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
9. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
TIME(2) Linux Programmer's Manual TIME(2)
NAME
time - get time in seconds
SYNOPSIS
#include <time.h>
time_t time(time_t *t);
DESCRIPTION
time() returns the time as the number of seconds since the Epoch, 1970-01-01 00:00:00 +0000 (UTC).
If t is non-NULL, the return value is also stored in the memory pointed to by t.
RETURN VALUE
On success, the value of time in seconds since the Epoch is returned. On error, ((time_t) -1) is returned, and errno is set appropriately.
ERRORS
EFAULT t points outside your accessible address space.
CONFORMING TO
SVr4, 4.3BSD, C89, C99, POSIX.1-2001. POSIX does not specify any error conditions.
NOTES
POSIX.1 defines seconds since the Epoch using a formula that approximates the number of seconds between a specified time and the Epoch.
This formula takes account of the facts that all years that are evenly divisible by 4 are leap years, but years that are evenly divisible
by 100 are not leap years unless they are also evenly divisible by 400, in which case they are leap years. This value is not the same as
the actual number of seconds between the time and the Epoch, because of leap seconds and because system clocks are not required to be syn-
chronized to a standard reference. The intention is that the interpretation of seconds since the Epoch values be consistent; see
POSIX.1-2008 Rationale A.4.15 for further rationale.
SEE ALSO
date(1), gettimeofday(2), ctime(3), ftime(3), time(7)
COLOPHON
This page is part of release 3.53 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
Linux 2011-09-09 TIME(2)