CHKCONFIG(8)						      System Manager's Manual						      CHKCONFIG(8)

NAME

       chkconfig - enable or disable system services

SYNOPSIS

       chkconfig -t|--terse [names]
       chkconfig -s|--set [name state]
       chkconfig -e|--edit [names]
       chkconfig -c|--check name [state]
       chkconfig -l|--list [--deps] [names]
       chkconfig -A|--allservices
       chkconfig -a|--add [names]
       chkconfig -d|--del [names]

DESCRIPTION

       chkconfig  is  used to manipulate the runlevel links at boot time (see init.d(7)).  It can be thought of as a frontend to insserv(8).  Chk-
       config can run in six different modes: terse list mode, set mode, edit mode, list mode, add mode and delete mode. The last three modes were
       added for compatiblity reasons.

TERSE LIST MODE

       This  mode lists the state of the specified services, or all known services if no service name was provided. Every printed line consists of
       the name of the service and the runlevels the service is configured for at the moment. If it is configured in  no  runlevel,  off  is  used
       instead,  if  it is configured in the runlevels defined as a default by the start script, on is used. If the service is an enabled inetd or
       xinetd service, inetd and xinetd are used. Inetd/xinetd services are configured in /etc/inetd.d and /etc/xinetd.d,  respectively.  You  can
       use the -A or --allservices parameter to get all services (even the boot.*-services) listed.

       If chkconfig is called without arguments, all services are listed in terse mode.

SET MODE

       Set  mode  is used to configure at which runlevel a service should be started. The arguments must be specified as pairs of service name and
       new state. You can use on and off as special states to select the default set of runlevels or to disable a service completely. You can  use
       inetd or xinetd to configure a service managed by the inetd/xinetd daemons.

       Insserv can calculate dependencies for only one service at the same time. To work around this limitation imposed by insserv, chkconfig uses
       the '-f' option of insserv when it reads the list of services from standard input. Note that --force switches off all dependency checks and
       could lead to depending services no longer working, use with care.

       If no services are specified, chkconfig reads lines from standard input. Each line must consist of a service/state pair. As this is exactly
       the output of the terse list mode, this can be used to reconfigure a service specification saved by a former run.

       If the option -f or --force is also given, insserv is called with a '-f' option.

EDIT MODE

       This mode is a combination of the terse list mode and set mode.	It writes the state of all specified services (or all known  services,	if
       no service was provided) into a temporary file, starts an editor and re-configures all services to reflect the states of the changed tempo-
       rary file.

CHECK MODE

       This mode can be used to check the state of a service.  chkconfig exits with a return code of '0' if the service is enabled in all  of  the
       specified  runlevels,  otherwise the exit status is '1'. If chkconfig is called with only a service name the current runlevel of the system
       is used for checking.

LIST MODE

       List mode prints for each specified service a line that consists of the service name and for runlevels zero to six on or off  depending	if
       the  service  will  be  started or not.	on will be printed in bright green if the output is written to a terminal. If the --deps option is
       given, the names of the services that must be started before this service is appended to each line. The inetd/xinetd services are listed in
       extra sections.

       You can use the -A or --allservices parameter to get all services (even the boot.*-services) listed.

ADD MODE

       Calls insserv to enable a service and uses list mode to display the new setting afterwards.

DEL MODE

       Same as add mode, but disable the service.

OTHER OPTIONS

       When  no service names are given on the command line, chkconfig defaults to all known services excluding those that are not enabled in run-
       levels 1 to 6 and start with 'boot.'.  Use the --allservices or -A option if you want to see such services as well.

EXAMPLES

	      chkconfig

       list the runlevel configuration of all known services

	      chkconfig apache

       list the runlevel configuration of the apache web server

	      chkconfig -t apache xntpd

       list the runlevel configuration of the apache web server and the network time protocol daemon.

	      chkconfig apache on

       configure the apache web server to be started on next boot time.

	      chkconfig apache 5

       configure the apache web server to be started only if the system reaches runlevel 5.

	      chkconfig apache 35

       configure the apache web server for runlevel 3 and 5.

	      chkconfig apache on xntpd off

       configure two services

	      chkconfig finger xinetd

       configure a xinetd service

	      chkconfig -A >~root/chkconfig.save

       backup the current configuration

	      chkconfig -s <~root/chkconfig.save

       restore the configuration

	      chkconfig -e apache xntpd

       change the runlevel configuration interactively

	      chkconfig -e

       change the runlevel configuration of all services interactively

FILES

       /etc/init.d/
	      path to the boot script base directory as required by the Linux Standard Base Specification (LSB).

       /etc/inetd.d/
	      path to the inetd services. See the inetd manpage to find out how to enable this feature.

       /etc/xinetd.d/
	      path to the xinetd services.

SEE ALSO

       init.d(7), init(7), inetd(8) xinetd(8) insserv(8)

COPYRIGHT

       2003 SuSE Linux AG, Nuernberg, Germany.

AUTHOR

       Michael Schroeder <mls@suse.de>

								     Oct 2006							      CHKCONFIG(8)