other machines with similar setup are sitting on the same subnet.
I want to shift one machine behind a cisco router that has one interface connected to the subnet 192.168.1.0 "192.168.1.1"
and the otherside on subnet 192.168.2.0 "192.168.2.1"
I want to add route to point from 192.168.1.0 to 192.168.2.0 and revrse.
what gateway should I use in the local machine and in the remote machine. qe1 or the router local interface
show in details please.
see attached file for sketch
hi,
below is the situation:
my server is in 128.10.200.xxx network.
i have a solaris computer running in a subnet. this computer got 2 nic card.
1 is 172.18.198.xxx , another 1 is 10.100.xxx.11
there is a machine stick with this computer, ip is 10.100.xxx.12
so, 10.100.xxx.11 and... (3 Replies)
Hi All, :(:confused:
I have scoured the web and can't find this anywhere.
What I am trying to do is set up a static route through an available gateway on a server, and then test connectivity through TELNET.
I have done this on AIX (I already had this procedure).
On AIX I would use SMIT. ... (7 Replies)
Does anyone know how to delete a an ip off the routing table ? i tried route delete 10.0.0.0 and gateway but it still comes back. i have 2 zones sharing one interface. help... (4 Replies)
hi all,
how do i make sure that the new routing should take effect on the os memory right away? what should i run after i add all the new "route add ....".
I have an example below:
bash-2.03# netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface... (1 Reply)
Hi,
I got problem of Sun Solaris 8 routing.
IP of SunA is 10.16.64.164, and have routing table:
10.16.64.0 10.16.64.164 U 1 19236 bge1
10.6.0.0 10.6.0.3 U 1 16534 bge0
224.0.0.0 10.6.0.3 U 1 ... (4 Replies)
Hello
Hope someone can help with this problem. We are running Solaris 10 with a current kernel patch of 142900-09.
We appear to be getting a serious issue with the routing table as shown below:
Output from netstat -rnv
Destination ....Mask ............Gateway ........Device... (2 Replies)
Hello All,
Problem is that redundancy doesn't work, probably a routing issue I need to get sorted out When 172.29.11.x net is down, neither node3 nor node4 is trying 172.29.12.x network,The problem lies in network 172.29.13.x
if 172.29.11.x network is down, node3/node4 should route to... (6 Replies)
Discussion started by: nadeemahmed
6 Replies
LEARN ABOUT DEBIAN
vlan-interfaces
VLAN-INTERFACES(5) File formats VLAN-INTERFACES(5)NAME
/etc/network/interfaces (vlan) - vlan extensions for the interfaces(5) file format
DESCRIPTION
/etc/network/interfaces contains network interface configuration information for the ifup(8) and ifdown(8) commands. This manpage
describes the vlan extensions to the standard interfaces(5) file format.
Primary extensions exist to make and destroy vlan interfaces, secondary extensions exist for ipv4 interface manipulation which are gener-
ally needed when using (a lot of) vlans.
VLAN CREATION
Vlan interface definitions exist of the vlan interface name, and an optional 'raw-device' parameter. Vlan interfaces are numbered 1 to
4095. You have the option to have interface names zero-padded to 4 numbers, or just the plain digits without leading zero. The following
example shows four ways to create a vlan with id 1 on interface eth0. They all result in different names.
iface eth0.1 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan1 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
iface eth0.0001 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan0001 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
# We don't have br support out of the box
iface br0.2 inet static
vlan-raw-device br0
address 192.168.1.1
netmask 255.255.255.0
# Aliases are ignored
iface br0.2:1 inet static
address 192.168.1.1
netmask 255.255.255.255
EXTRA IFACE OPTIONS
Usually someone who uses vlans also wants to do some other manipulations with the ip stack or interface.
vlan-raw-device devicename
Indicates the device to create the vlan on. This is ignored when the devicename is part of the vlan interface name.
ip-proxy-arp 0|1
Turn proxy-arp off or on for this specific interface. This also works on plain ethernet like devices.
ip-rp-filter 0|1|2
Set the return path filter for this specific interface. This also works on plain ethernet like devices.
hw-mac-address mac-address
This sets the mac address of the interface before bringing it up. This works on any device that allows setting the hardware address
with the ip command.
AUTHOR
This manpage was adapted from interfaces(5) by Ard van Breemen <ard@kwaak.net>
SEE ALSO vconfig(8)interfaces(5)vlan September 30 2007 VLAN-INTERFACES(5)