03-09-2009
where did you get that file? ifcfg-eth0 is a redhat style config and opensuse usually puts the MAC address string in the eth file. Have you tried removing and reconfiguring your network device?
10 More Discussions You Might Find Interesting
1. IP Networking
I have installed Solaris 8.0 and want to find out how can I go in and change my network setup and external IP setup. At the moment system running but I can not connect to the internet. But my lan card shows that I am on the network. I also get some advice that I should check the $Socks but how do I... (1 Reply)
Discussion started by: Cdrive
1 Replies
2. UNIX for Dummies Questions & Answers
Im on XP now but when im on linux how do I connect to the internet?
I don't think AOL works with it but are there any free programs that I can use with it? (8 Replies)
Discussion started by: NoPepsiForYou
8 Replies
3. UNIX for Dummies Questions & Answers
Hi all,
Is it possible (as I only have dial-up) to utilise my existing WinXP PC as a gateway to the internet for my 2nd PC (RH 8.0)?? .So connect with XP and have RH use a network connection (I guess) through the XP box and to the internet.
If so, could I please have some links thrown my... (1 Reply)
Discussion started by: Cameron
1 Replies
4. UNIX for Dummies Questions & Answers
I am using solaris 10 with pentium 3. I have two network cards but none of them come up when i run <ifconfig -a> in command line. The two cards I have are : Linksys LNE 100TX and Netgear FA311. Does solaris 10 support these NICs or do I have to dowload the drivers for them.
If so, can anyone... (1 Reply)
Discussion started by: fidjouss
1 Replies
5. Linux
Hi,
I can ping www.yahoo.com (then domain name server is OK) but I can not navigate by Motzila to www.yahoo.com or any other Web Site.
What can be the problem ? Mozila is configured in preference /advance to go automaticaly on WEB.
We are under RED HAT AS3.
What should I check ?
Many thanks... (1 Reply)
Discussion started by: big123456
1 Replies
6. UNIX for Dummies Questions & Answers
I have just installed Linux and everything looks great, but how do I get my browser (Mozilla) to connect to my internet service provider?
I have a cable connection to Bigpond in Australia, if that means anything - the ISP will not provide support for Linux.
Your help would be greatly... (2 Replies)
Discussion started by: openhead
2 Replies
7. Solaris
hi there, hope your chakras are all doing well :-)
just installed solaris 10 on my laptop, all seems fine except the internet. How can i connect on a DSL line?. spent 7 days and 3 nights trying but couldnt find the starting point....
alikun (22 Replies)
Discussion started by: alikun
22 Replies
8. UNIX for Advanced & Expert Users
Hi Guys,
I have trouble connecting to ftp server. My task is to connect to the proxy server and get the latest file to the local machine. It works fine when i do the same steps manually. I've been trying to do it in multiple ways but im just not able to connect. When i check the log, this is what... (4 Replies)
Discussion started by: stunnerz_84
4 Replies
9. SCO
Hi, I have a router, 192.168.1.1, and an internet router, 10.0.0.138. I have connected the server to the 1st router and assigned it a IP address of 192.168.1.1. I can ping both routers successfully but I have no access to internet. Any suggestions? sco5.0.7 (11 Replies)
Discussion started by: juan.navarrete
11 Replies
10. Ubuntu
Note: I originally posted this question on unix.stackexchange.com. But as my question was down-voted within an hour of asking, I came to the conclusion that perhaps I need to quit attempting to get help on StackExchange or that my inquiry is simply moronic. If anyone feels that my question is not... (7 Replies)
Discussion started by: AntumDeluge
7 Replies
LEARN ABOUT SUSE
ifcfg-bonding
IFCFG-BONDING(5) Network configuration IFCFG-BONDING(5)
NAME
ifcfg-bonding - interface bonding configuration
SYNOPSIS
/etc/sysconfig/network/ifcfg-bond*
Bonding Interfaces
To setup a bonding interface you need a configuration file ifcfg-bond<X> with the usual network settings. But you must add additional vari-
ables
BONDING_MASTER
must be set to 'yes' to identify this interface as a bonding interface
BONDING_SLAVE_<X>
here you specify the interface name representing the slave network interfaces.
BONDING_MODULE_OPTS
contains bonding options. Here you can set interface timeouts or working modes ('mode=active-backup' for backup mode). For addi-
tional information take a look into the documentation mentioned at the bottom. Note, that this options are not passed as parameters
to the bonding kernel module any more, but set via sysfs interface. This variable will be renamed in the feature.
BONDING_SKIP_REMOVE_WORKAROUND
When set to "yes", a bonding interface will be not removed while ifdown any more to avoid problems, e.g. when some third party ker-
nel module, such as Veritas 'llt' module, does not react correctly to the UNREGISTER event and does not remove its references to the
bonding interface causing all network related operation to stuck.
Note: the bonding options are not reverted when this option is enabled and it is required to either explicitly keep the old options
and set them to their default setting on bonding configuration changes or to reboot.
Example
Example for a bonding interface on eth0 and eth1 using the backup mode
ifcfg-bond0
STARTMODE='onboot'
BOOTPROTO='static'
IPADDR='192.168.0.1/24'
BONDING_MASTER='yes'
BONDING_SLAVE_0='eth0'
BONDING_SLAVE_1='eth1'
BONDING_MODULE_OPTS='mode=active-backup miimon=100'
Additional Information
For additional and more general information take a look into /usr/src/linux/Documentation/networking/bonding.txt. Maybe you need to
install the kernel sources to get this additional documentation.
The configuration of routes for this kind of interface does not differ from ordinary interfaces. See man routes for details.
BUGS
Please report bugs at <http://www.suse.de/feedback>
AUTHOR
Christian Zoz <zoz@suse.de> -- ifup script
Wilken Gottwalt <wgottwalt@suse.de> -- ifcfg-bonding manual page
SEE ALSO
ifcfg(5), ifup(8).
sysconfig April 2005 IFCFG-BONDING(5)