Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: vxdisk list output showing extra LUNs
Special Forums Hardware Filesystems, Disks and Memory vxdisk list output showing extra LUNs Post 302295313 by bond_ankur on Saturday 7th of March 2009 10:16:52 AM
Old 03-07-2009
hi fren

i hv 30 volumes on 30 disk only

There are 4 storages attached to the server wid solaris 10
al 4 are sun 6140
i have 2 SAN switches for 4 storages as i cn max add 3 storages

one volume has been assigned to the disk
i cn c dat in storage too
there is no problem from storage end

As far as i knw only those LUNs are shown in vsdisk list output that you hv assigned in the storage
plz correct me if i am wrong here
Now as i hv 2 SAN switches 4 paths should exist for each disk
bt nw whn i chek the paths assigned
via luxadm

i gt the following output
jest chek the last 7 logical disk ( they hv 2 paths )

Node WWN:200600a0b84853c0 Device TypeSmilieisk device
Logical Path:/dev/rdsk/c3t201600A0B84853C0d65s2
Logical Path:/dev/rdsk/c4t201700A0B84853C0d65s2
Logical Path:/dev/rdsk/c5t201600A0B84853C0d65s2
Logical Path:/dev/rdsk/c6t201700A0B84853C0d65s2
Node WWN:200600a0b84853c0 Device TypeSmilieisk device
Logical Path:/dev/rdsk/c3t201600A0B84853C0d66s2
Logical Path:/dev/rdsk/c4t201700A0B84853C0d66s2
Logical Path:/dev/rdsk/c5t201600A0B84853C0d66s2
Logical Path:/dev/rdsk/c6t201700A0B84853C0d66s2
Node WWN:200600a0b84853c0 Device TypeSmilieisk device
Logical Path:/dev/rdsk/c3t201600A0B84853C0d67s2
Logical Path:/dev/rdsk/c4t201700A0B84853C0d67s2
Logical Path:/dev/rdsk/c5t201600A0B84853C0d67s2
Logical Path:/dev/rdsk/c6t201700A0B84853C0d67s2
Node WWN:200600a0b84853c0 Device TypeSmilieisk device
Logical Path:/dev/rdsk/c4t201700A0B84853C0d2s2
Logical Path:/dev/rdsk/c6t201700A0B84853C0d2s2
Node WWN:200600a0b84853c0 Device TypeSmilieisk device
Logical Path:/dev/rdsk/c4t201700A0B84853C0d7s2
Logical Path:/dev/rdsk/c6t201700A0B84853C0d7s2
Node WWN:200600a0b84853c0 Device TypeSmilieisk device
Logical Path:/dev/rdsk/c4t201700A0B84853C0d9s2
Logical Path:/dev/rdsk/c6t201700A0B84853C0d9s2
Node WWN:200600a0b84853c0 Device TypeSmilieisk device
Logical Path:/dev/rdsk/c4t201700A0B84853C0d10s2
Logical Path:/dev/rdsk/c6t201700A0B84853C0d10s2
Node WWN:200600a0b84853c0 Device TypeSmilieisk device
Logical Path:/dev/rdsk/c4t201700A0B84853C0d12s2
Logical Path:/dev/rdsk/c6t201700A0B84853C0d12s2
Node WWN:200600a0b84853c0 Device TypeSmilieisk device
Logical Path:/dev/rdsk/c4t201700A0B84853C0d13s2
Logical Path:/dev/rdsk/c6t201700A0B84853C0d13s2
Node WWN:200600a0b84853c0 Device TypeSmilieisk device
Logical Path:/dev/rdsk/c4t201700A0B84853C0d59s2
Logical Path:/dev/rdsk/c6t201700A0B84853C0d59s2

i am right nw very cnfused .....
are these 2 problems interrelated or which is due to which and DMP has nt been assigned as i need the logical disks to assign 2 diff disk grps

i dunno if i hv explained myself very clearly
plz lemme knw
this is d only prb whr i hv been stuck for quite a time
 

10 More Discussions You Might Find Interesting

1. Shell Programming and Scripting

Showing extra line/record in file

Hello everybody, My job is to load the data from Oracle table to flat file and from flat file to oracle table using ETL tool Informatica. My flat files are fixed width. In the first phase, it is loading 66351 records into data file through tool. When I checked through wc -l <data filename> it is... (1 Reply)
Discussion started by: srivsn
1 Replies

2. Filesystems, Disks and Memory

Showing an extra record/line

Hello everybody, I am working on ETL side. My job is to load the data from Oracle table to flat file and from flat file to oracle table using ETL tool Informatica. My flat files are fixed width. In the first phase, it is loading 66351 records into data file through tool. When I checked through... (1 Reply)
Discussion started by: srivsn
1 Replies

3. Shell Programming and Scripting

Extra output in the script

Hi , I am trying to execute the following script. #!/bin/sh find . -name "common.log.diff" if ; then cp common.log common.log.diff diff common.log common.log.diff > DIFFERENCE.log cp common.log common.log.diff grep "ERROR" DIFFERENCE.log if ; then echo "1" else echo "0" fi... (5 Replies)
Discussion started by: himvat
5 Replies

4. Solaris

luxadm probe and vxdisk list don't matchup

I have a new SAN (Fujitsu Eternus 2000) and am trying to setup a veritas cluster on it, however veritas does not see all of the vluns I have exposed to the box. The OS does see them though. I have seen a lot of post about this, but it seems they are about people having just the opposite problem... (0 Replies)
Discussion started by: timothy.edwards
0 Replies

5. Shell Programming and Scripting

Output from sql session having an extra whitespace

I am running a sql session within a shell script. Later I am performing some validations on the value coming from the sql session. The problem is that, the value I am getting from sql session have an extra white space at the begining(I am actually, assigning the outcome of the sql session to a... (5 Replies)
Discussion started by: mady135
5 Replies

6. Solaris

Adding new luns to mpxio config - showing up twice in format.

Hi, I have a sun 440, it already has LUN's configured with MPXIO. I just had more LUNS added, I did devfsadm and cfgadm -al, and they're showing up twice in "Format". :confused: There are no new fiber cables or HBA's involved, same physical setup, just adding LUNS. Aren't they... (0 Replies)
Discussion started by: BG_JrAdmin
0 Replies

7. Solaris

Mpathadm showing no paths to 1 lun, others luns are fine

Hi, I've noticed that mpathadm states that one of our luns has no active paths: /dev/rdsk/c6t60000970000298700009533031324333d0s2 Total Path Count: 4 Operational Path Count: 4 /dev/rdsk/c6t60000970000298700009533031333037d0s2 ... (3 Replies)
Discussion started by: badoshi
3 Replies

8. Shell Programming and Scripting

Now showing the correct output

Hello I am working on one script where I am trying to display all the directories which is inside the workspace but somehow it is giving me weird output and this is occurring only with one directory other also having the result.html file inside the directory. for i in `ls -1 | egrep -iv... (2 Replies)
Discussion started by: anuragpgtgerman
2 Replies

9. Shell Programming and Scripting

Extra Space in output - remove

Hi All I am trying to perform the below operation -count=`cat abc.txt | wc -l` echo$count 5 Head=Start"$DATE"00000"$count"File echo $HEAD START15020300000 5File There is a space coming before 5 which is not needed . How to ignore that . (4 Replies)
Discussion started by: honey26
4 Replies

10. Shell Programming and Scripting

Extra data in output file

Gents, I did a small scritp called make_file It read file1.txt file and generate an output as attached.. But the script is showing more extra information not needed. I have attached the output file as desired. Could you please help to fix this scrip to get the correct output Thanks... (4 Replies)
Discussion started by: jiam912
4 Replies

LEARN ABOUT LINUX

fcinfo

fcinfo(1M)																fcinfo(1M)

NAME

       fcinfo - Fibre Channel HBA Port Command Line Interface

SYNOPSIS

       fcinfo hba-port [-l] [HBA_port_WWN...]

       fcinfo  remote-port [-ls] [-p HBA_port_WWN] [REMOTE_port_WWN...]

       fcinfo [-V]

       fcinfo [-?]

       fcinfo  is  a  command  line interface that collects administrative information on fibre channel host bus adapter (HBA) ports on a host. It
       also collects data on any fibre channel targets that may be connected to those ports in a Storage Area Network (SAN).

   SUBCOMMANDS
       The following subcommands are supported:

       hba-port

	   Lists information for the HBA port referenced by the specified HBA_port_WWN. If HBA_port_WWN is not specified, all  fibre  channel  HBA
	   ports on the host will be listed.

       remote-port

	   Lists  the remote-port information for those remote ports that are specified. If no REMOTE_port_WWN is specified, all remote ports that
	   are visible through HBA_port_WWN are listed.

OPTIONS

       The following options are supported:

       -l, --linkstat

	   Lists the link error statistics information for the port referenced by the specified HBA_port_WWN or REMOTE_port_WWN.

       -p HBA_port_WWN, --port HBA_port_WWN

	   Retrieve remote port information from the HBA_port_WWN of the local HBA port on the host. The -p option  can  only  be  used  with  the
	   remote-port subcommand and is a mandatory option.

       -s, --scsi-target

	   Lists  the SCSI target information for all remote ports the user has asked for. The -p, --port option must always be specified and must
	   be a valid HBA port on the host. This HBA port will be used as the initiator for which to retrieve the SCSI level  target  information.
	   Note that this will only function on remote port fibre channel World-Wide Names that support an FC4 type of SCSI.

       -V, --version

	   Prints the version information.

       -?, --help

	   Prints the usage information.

EXAMPLES

       Example 1: Listing all HBA ports

       The following command lists all fibre channel HBA ports on the host:

       # fcinfo hba-port

       HBA Port WWN: 210000e08b074cb5
	       OS Device Name: /dev/cfg/c1
	       Manufacturer: QLogic Corp.
	       Model: 375-3108-xx
	       Type: N-port
	       State: online
	       Supported Speeds: 1Gb 2Gb
	       Current Speed: 2Gb
	       Node WWN: 200000e08b074cb5
       HBA Port WWN: 210100e08b274cb5
	       OS Device Name: /dev/cfg/c2
	       Manufacturer: QLogic Corp.
	       Model: 375-3108-xx
	       Type: N-port
	       State: online
	       Supported Speeds: 1Gb 2Gb
	       Current Speed: 2Gb
	       Node WWN: 200100e08b274cb5
       HBA Port WWN: 210000e08b072ab5
	       OS Device Name: /dev/cfg/c3
	       Manufacturer: QLogic Corp.
	       Model: 375-3108-xx
	       Type: L-port
	       State: online
	       Supported Speeds: 1Gb 2Gb
	       Current Speed: 2Gb
	       Node WWN: 200000e08b072ab5
       HBA Port WWN: 210100e08b272ab5
	       OS Device Name: /dev/cfg/c4
	       Manufacturer: QLogic Corp.
	       Model: 375-3108-xx
	       Type: N-port
	       State: online
	       Supported Speeds: 1Gb 2Gb
	       Current Speed: 2Gb
	       Node WWN: 200100e08b272ab5

       Example 2: Listing HBA ports and link statistics

       The following command lists information for the HBA ports and the link statistics for those ports:

       # fcinfo hba-port -l 210000e08b074cb5 210100e08b274cb5

       HBA Port WWN: 210000e08b074cb5
	       OS Device Name: /dev/cfg/c1
	       Manufacturer: QLogic Corp.
	       Model: 375-3108-xx
	       Type: N-port
	       State: online
	       Supported Speeds: 1Gb 2Gb
	       Current Speed: 2Gb
	       Node WWN: 200000e08b074cb5
	       Link Error Statistics:
		       Link Failure Count: 0
		       Loss of Sync Count: 0
		       Loss of Signal Count: 0
		       Primitive Seq Protocol Error Count: 0
		       Invalid Tx Word Count: 0
		       Invalid CRC Count: 0
       HBA Port WWN: 210100e08b274cb5
	       OS Device Name: /dev/cfg/c2
	       Manufacturer: QLogic Corp.
	       Model: 375-3108-xx
	       Type: N-port
	       State: online
	       Supported Speeds: 1Gb 2Gb
	       Current Speed: 2Gb
	       Node WWN: 200100e08b274cb5
	       Link Error Statistics:
		       Link Failure Count: 0
		       Loss of Sync Count: 0
		       Loss of Signal Count: 0
		       Primitive Seq Protocol Error Count: 0
		       Invalid Tx Word Count: 0
		       Invalid CRC Count: 0

       Example 3: Listing all remote ports

       The following command lists all remote ports that are visible through the given HBA port:

       # fcinfo remote-port -p 210100e08b274cb5

       Remote Port WWN: 50020f230000b4af
	       Active FC4 Types: SCSI
	       SCSI Target: yes
	       Node WWN: 50020f200000b4af
       Remote Port WWN: 210000e08b07daa6
	       Active FC4 Types: SCSI
	       SCSI Target: no
	       Node WWN: 200000e08b07daa6
       Remote Port WWN: 20030003ba27c788
	       Active FC4 Types: SCSI
	       SCSI Target: yes
	       Node WWN: 10000003ba27c788
       Remote Port WWN: 210000e08b096a60
	       Active FC4 Types: SCSI,IP
	       SCSI Target: no
	       Node WWN: 200000e08b096a60

       Example 4: Listing remote ports and link statistics

       The following command lists information for the remote ports and the link statistics for those ports:

       # fcinfo remote-port -l -p 210100e08b272ab5

       Remote Port WWN: 210100e08b296a60
	       Active FC4 Types: SCSI,IP
	       SCSI Target: no
	       Node WWN: 200100e08b296a60
	       Link Error Statistics:
		       Link Failure Count: 0
		       Loss of Sync Count: 0
		       Loss of Signal Count: 0
		       Primitive Seq Protocol Error Count: 0
		       Invalid Tx Word Count: 0
		       Invalid CRC Count: 0
       Remote Port WWN: 20030003ba27d56d
	       Active FC4 Types: SCSI
	       SCSI Target: yes
	       Node WWN: 10000003ba27d56d
	       Link Error Statistics:
		       Link Failure Count: 0
		       Loss of Sync Count: 4765165
		       Loss of Signal Count: 4765165
		       Primitive Seq Protocol Error Count: 0
		       Invalid Tx Word Count: 0
		       Invalid CRC Count: 0
       Remote Port WWN: 210100e08b27f7a6
	       Active FC4 Types: SCSI
	       SCSI Target: no
	       Node WWN: 200100e08b27f7a6
	       Link Error Statistics:
		       Link Failure Count: 0
		       Loss of Sync Count: 0
		       Loss of Signal Count: 0
		       Primitive Seq Protocol Error Count: 0
		       Invalid Tx Word Count: 0
		       Invalid CRC Count: 0
       Remote Port WWN: 50020f230000b897
	       Active FC4 Types: SCSI
	       SCSI Target: yes
	       Node WWN: 50020f200000b897
	       Link Error Statistics:
		       Link Failure Count: 0
		       Loss of Sync Count: 7
		       Loss of Signal Count: 7
		       Primitive Seq Protocol Error Count: 0
		       Invalid Tx Word Count: 0
		       Invalid CRC Count: 0
       Remote Port WWN: 210100e08b27daa6
	       Active FC4 Types: SCSI
	       SCSI Target: no
	       Node WWN: 200100e08b27daa6
	       Link Error Statistics:
		       Link Failure Count: 0
		       Loss of Sync Count: 0
		       Loss of Signal Count: 0
		       Primitive Seq Protocol Error Count: 0
		       Invalid Tx Word Count: 0
		       Invalid CRC Count: 0
       Remote Port WWN: 210000e08b074cb5
	       Active FC4 Types: SCSI,IP
	       SCSI Target: no
	       Node WWN: 200000e08b074cb5
	       Link Error Statistics:
		       Link Failure Count: 0
		       Loss of Sync Count: 0
		       Loss of Signal Count: 0
		       Primitive Seq Protocol Error Count: 0
		       Invalid Tx Word Count: 0
		       Invalid CRC Count: 0
       Remote Port WWN: 210100e08b296060
	       Active FC4 Types: SCSI
	       SCSI Target: no
	       Node WWN: 200100e08b296060
	       Link Error Statistics:
		       Link Failure Count: 0
		       Loss of Sync Count: 0
		       Loss of Signal Count: 0
		       Primitive Seq Protocol Error Count: 0
		       Invalid Tx Word Count: 0
		       Invalid CRC Count: 0

       Example 5: Listing all SCSI targets and link statistics

       The following command lists all remote ports as well as the link statistics and scsi-target information:

       # fcinfo remote-port  -sl -p 210100e08b272ab5

       Remote Port WWN: 210100e08b296a60
	       Active FC4 Types: SCSI,IP
	       SCSI Target: no
	       Node WWN: 200100e08b296a60
	       Link Error Statistics:
		       Link Failure Count: 0
		       Loss of Sync Count: 0
		       Loss of Signal Count: 0
		       Primitive Seq Protocol Error Count: 0
		       Invalid Tx Word Count: 0
		       Invalid CRC Count: 0
       Remote Port WWN: 20030003ba27d56d
	       Active FC4 Types: SCSI
	       SCSI Target: yes
	       Node WWN: 10000003ba27d56d
	       Link Error Statistics:
		       Link Failure Count: 0
		       Loss of Sync Count: 4765165
		       Loss of Signal Count: 4765165
		       Primitive Seq Protocol Error Count: 0
		       Invalid Tx Word Count: 0
		       Invalid CRC Count: 0
	       LUN: 0
		 Vendor: SUN
		 Product: T4
		 OS Device Name: /dev/rdsk/c4t20030003BA27D56Dd0s2
	       LUN: 1
		 Vendor: SUN
		 Product: T4
		 OS Device Name: /dev/rdsk/c4t20030003BA27D56Dd1s2
       Remote Port WWN: 210100e08b27f7a6
	       Active FC4 Types: SCSI
	       SCSI Target: no
	       Node WWN: 200100e08b27f7a6
	       Link Error Statistics:
		       Link Failure Count: 0
		       Loss of Sync Count: 0
		       Loss of Signal Count: 0
		       Primitive Seq Protocol Error Count: 0
		       Invalid Tx Word Count: 0
		       Invalid CRC Count: 0
       Remote Port WWN: 50020f230000b897
	       Active FC4 Types: SCSI
	       SCSI Target: yes
	       Node WWN: 50020f200000b897
	       Link Error Statistics:
		       Link Failure Count: 0
		       Loss of Sync Count: 7
		       Loss of Signal Count: 7
		       Primitive Seq Protocol Error Count: 0
		       Invalid Tx Word Count: 0
		       Invalid CRC Count: 0
	       LUN: 0
		 Vendor: SUN
		 Product: T300
		 OS Device Name: Unknown
	       LUN: 1
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d1s2
	       LUN: 2
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d2s2
	       LUN: 3
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d3s2
	       LUN: 4
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d4s2
	       LUN: 5
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d5s2
	       LUN: 6
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d6s2
	       LUN: 7
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d7s2
	       LUN: 8
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d8s2
	       LUN: 9
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d9s2
	       LUN: 10
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d10s2
	       LUN: 11
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d11s2
	       LUN: 12
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d12s2
	       LUN: 13
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d13s2
	       LUN: 14
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d14s2
	       LUN: 15
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d15s2
       Remote Port WWN: 210100e08b27daa6
	       Active FC4 Types: SCSI
	       SCSI Target: no
	       Node WWN: 200100e08b27daa6
	       Link Error Statistics:
		       Link Failure Count: 0
		       Loss of Sync Count: 0
		       Loss of Signal Count: 0
		       Primitive Seq Protocol Error Count: 0
		       Invalid Tx Word Count: 0
		       Invalid CRC Count: 0
       Remote Port WWN: 210000e08b074cb5
	       Active FC4 Types: SCSI,IP
	       SCSI Target: no
	       Node WWN: 200000e08b074cb5
	       Link Error Statistics:
		       Link Failure Count: 0
		       Loss of Sync Count: 0
		       Loss of Signal Count: 0
		       Primitive Seq Protocol Error Count: 0
		       Invalid Tx Word Count: 0
		       Invalid CRC Count: 0
       Remote Port WWN: 210100e08b296060
	       Active FC4 Types: SCSI
	       SCSI Target: no
	       Node WWN: 200100e08b296060
	       Link Error Statistics:
		       Link Failure Count: 0
		       Loss of Sync Count: 0
		       Loss of Signal Count: 0
		       Primitive Seq Protocol Error Count: 0
		       Invalid Tx Word Count: 0
		       Invalid CRC Count: 0

       Example 6: Listing SCSI target information

       The following command lists all remote ports as well as the scsi-target information:

       # fcinfo remote-port  -s -p 210100e08b272ab5

       Remote Port WWN: 210100e08b296a60
	       Active FC4 Types: SCSI,IP
	       SCSI Target: no
	       Node WWN: 200100e08b296a60
       Remote Port WWN: 20030003ba27d56d
	       Active FC4 Types: SCSI
	       SCSI Target: yes
	       Node WWN: 10000003ba27d56d
	       LUN: 0
		 Vendor: SUN
		 Product: T4
		 OS Device Name: /dev/rdsk/c4t20030003BA27D56Dd0s2
	       LUN: 1
		 Vendor: SUN
		 Product: T4
		 OS Device Name: /dev/rdsk/c4t20030003BA27D56Dd1s2
       Remote Port WWN: 210100e08b27f7a6
	       Active FC4 Types: SCSI
	       SCSI Target: no
	       Node WWN: 200100e08b27f7a6
       Remote Port WWN: 50020f230000b897
	       Active FC4 Types: SCSI
	       SCSI Target: yes
	       Node WWN: 50020f200000b897
	       LUN: 0
		 Vendor: SUN
		 Product: T300
		 OS Device Name: Unknown
	       LUN: 1
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d1s2
	       LUN: 2
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d2s2
	       LUN: 3
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d3s2
	       LUN: 4
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d4s2
	       LUN: 5
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d5s2
	       LUN: 6
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d6s2
	       LUN: 7
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d7s2
	       LUN: 8
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d8s2
	       LUN: 9
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d9s2
	       LUN: 10
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d10s2
	       LUN: 11
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d11s2
	       LUN: 12
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d12s2
	       LUN: 13
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d13s2
	       LUN: 14
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d14s2
	       LUN: 15
		 Vendor: SUN
		 Product: T300
		 OS Device Name: /dev/rdsk/c4t50020F230000B897d15s2
       Remote Port WWN: 210100e08b27daa6
	       Active FC4 Types: SCSI
	       SCSI Target: no
	       Node WWN: 200100e08b27daa6
       Remote Port WWN: 210000e08b074cb5
	       Active FC4 Types: SCSI,IP
	       SCSI Target: no
	       Node WWN: 200000e08b074cb5
       Remote Port WWN: 210100e08b296060
	       Active FC4 Types: SCSI
	       SCSI Target: no
	       Node WWN: 200100e08b296060

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNW			   |
       +-----------------------------+-----------------------------+
       |Interface Stability	     |Evolving			   |
       +-----------------------------+-----------------------------+

       attributes(5)

ERROR MESSAGES

       Errors that can occur in addition to the errors normally associated with system administration commands:

       HBA_port_WWN: not found

       REMOTE_port_WWN: not found

								    17 Feb 2005 							fcinfo(1M)
All times are GMT -4. The time now is 01:24 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy