hi all,
i'm very new to scripting and have the folllowing issue. I have used a few commands to get a list of numbers, but I need to strip away the non-numeric ones, and then need a total of all values. any ideas?
root@unixserver # cat myfile | awk '{print $8}'| sort -rn
1504
1344
896
704... (2 Replies)
I am getting back on the C++ programming after many years away. I recently received an SDK that has code like this where numeric values end in 'U'. What does this mean?
if ((ptr % 16U) == 0U)
return buffer; (3 Replies)
How to check if the file contains only numeric values.
I don't want to read entire file it eats lot of cpu
Or any way which consumes less memory n cpu..
Please suggest
-S (2 Replies)
hi
i have two types of file
1. temp.0000000001.data (10 digit numeric)
2. temp.000000001.data (9 digit numeric)
i want to search a file which is having 10 digit numeric in between the file name.
i use command like this..
ls | grep temp.^*.data
but this will give both the files as... (2 Replies)
Hey guys & gals,
I am hoping for some advice on a sed or awk command that will
allow to only print lines from a file that contain 3 numeric values.
From previous searches here I saw that ygemici used the sed command
to remove lines containing more than 3 numeric values ;
however how... (3 Replies)
Hi All ,
I have a small code that checks pattern of digits entered in unix mode .
$ echo 201202 | wc -c
7 /* output*/
When i run same command in AIX 5.1 , i am getting output with some initial blanks
$ echo 201202 | wc -c
7 ... (4 Replies)
I have a code like this
v_num=9
comp_num=39
if
then
echo "pass"
fi
echo "end"
I am getting an error
ksh: v_num=99
comp_num=39
if
then
echo "pass"
fi
echo "end" (3 Replies)
From googling and reading man pages I figured out this sorts the first column by numeric values.
sort -g -k 1,1
Why does the -n option not work? The man pages were a bit confusing.
And what if I want to sort the second column numerically? I haven't been able to figure that out. The file... (7 Replies)
Hi All,
I am trying to replace a certain value from one place in a file . In the below file at position 35 I will have 8 I need to modify all 8 in that position to 7
I tried
awk '{gsub("8","7",$35)}1' infile > outfile ----> not working
sed -i 's/8/7'g' infile --- it is replacing all... (3 Replies)
Discussion started by: arunkumar_mca
3 Replies
LEARN ABOUT DEBIAN
printfail
MESSAGES(3) libbash messages Library Manual MESSAGES(3)NAME
messages -- libbash library that implements a set of functions to print standard status messages
SYNOPSIS
printOK [indent]
printFAIL [indent]
printNA [indent]
printATTN [indent]
printWAIT [indent]
DESCRIPTION
General
messages is a collection of functions to print standard status messages - those [ OK ] and [FAIL] messages you see during Linux boot process.
The function list:
printOK Prints a standard [ OK ] message (green)
printFAIL Prints a standard [FAIL] message (red)
printNA Prints a standard [ N/A] message (yellow)
printATTN Prints a standard [ATTN] message (yellow)
printWAIT Prints a standard [WAIT] message (yellow)
Detailed interface description follows.
indent
Column to move to before printing.
Default indent is calculated as TTY_WIDTH-10. If current tty width can not be determined (for example, in case of serial console), it
defaults to 80, so default indent is 80-10=10
FUNCTIONS DESCRIPTIONS
printOK [indent]
Prints a standard [ OK ] message (green)
printFAIL [indent]
Prints a standard [FAIL] message (red)
printNA [indent]
Prints a standard [ N/A] message (yellow)
printATTN [indent]
Prints a standard [ATTN] message (yellow)
printWAIT [indent]
Prints a standard [WAIT] message (yellow)
EXAMPLES
Run a program named MyProg, and report it's success or failure:
echo -n 'Running MyProg...'
printWAIT
if MyProg ; then
printOK
else
printFAIL
fi
AUTHORS
Hai Zaar <haizaar@haizaar.com>
Gil Ran <gil@ran4.net>
SEE ALSO ldbash(1), libbash(1)Linux Epoch Linux