03-05-2009
Quote:
Originally Posted by
Lieyza
Thank you for reply..really appreciate!vWhere should i type that code?
command line. Put it in /etc/sysctl.conf to make it permanent (uh, but the syntax will be like this: var = value)
9 More Discussions You Might Find Interesting
1. IP Networking
I am running RH7.3 on a compaq presario box. The network card is a Linksys one. I am only able to communicate with the local network (only the local IPs are accessible). When I try to ping another box I get a "Connect: Network is unreachable" message. What could be the problem.
Thanks in... (2 Replies)
Discussion started by: skotapal
2 Replies
2. IP Networking
I have a solaris 9 system that cannot get to the internet and cannot ping outside of the router. I can ping any other system on this campus but when i try to ping any other system outside of the campus im on i get unreachable.
Here is the systems info:
ip: 10.241.3.254
subnet: 255.254.0.0... (7 Replies)
Discussion started by: meyersp
7 Replies
3. Filesystems, Disks and Memory
Hi,
I have a network disk that runs windows xp embedded. It doesnt support NFS.
But Samba is supported.
How do i connect to it through solaris 9. What are the steps required.
I have the IP address of the drive.
Thanks (1 Reply)
Discussion started by: R00tSc0rpi0n
1 Replies
4. Solaris
I want to install Solaris 11 Express on my x86 system.
I'm facing network driver problems.
I've 3 network cards:
1. Intel(R) 82579V Gigabit Network Connection
In Device Driver Utility, This device is displayed as Ethernet controller, Driver is UNK and its highlighted in RED.
2. Belkin... (3 Replies)
Discussion started by: choudharypranay
3 Replies
5. AIX
Hi,
I have a task requested by my boss to create a script to enable a server to connect to a vpn network and then to connect to another server to upload some data...
How can I connect to a vpn network from AIX server? via telnet? ssh?
I have tried to google but mostly the answers are... (1 Reply)
Discussion started by: mushr00m
1 Replies
6. Shell Programming and Scripting
Hello all,
Here is the explanation of my problem:
I have a cronjob that connects to a NAS to do backups from my laptop to this NAS device.
The script that I wrote does check if there is a host (the NAS) responding on 192.168.1.10 and tries to connect to it with the following command:
mount -v... (3 Replies)
Discussion started by: freddie50
3 Replies
7. Shell Programming and Scripting
I am trying to write a script for my own use that will allow me to connect to network devices, then run a set of commands.
I start with a list of ips in a text file. Each ip is on its own line.
I start with a second file of commands. Each command on one line.
for illustration .. the cmd.txt... (2 Replies)
Discussion started by: popeye
2 Replies
8. UNIX for Dummies Questions & Answers
Have -
-3 HP Proliant G4P servers - Debian (wheezy)
-3 RaspPI's - Raspian
-Unmanaged switch that all 6 can ssh into each other with via eth0
-Router (w wifi and 5 ports) - on eth1 of the three G4p's of protocol dhcp
Want:
To let the six servers, in my basement run, since the HPs are... (5 Replies)
Discussion started by: sas
5 Replies
9. Ubuntu
I run lubuntu from usb (try lubuntu, it's not install on my pc )
And i try to connect to network
I see the network name
And i put the pass
But it's not connect..
I tried to open hot spot on my phone and try to connect and it's not connect
I have edumax n150
Try to install new driver -... (0 Replies)
Discussion started by: popcoern
0 Replies
LEARN ABOUT X11R4
ip-token
IP-TOKEN(8) Linux IP-TOKEN(8)
NAME
ip-token - tokenized interface identifier support
SYNOPSIS
ip token { COMMAND | help }
ip token set TOKEN dev DEV
ip token del dev DEV
ip token get [ dev DEV ]
ip token [ list ]
DESCRIPTION
IPv6 tokenized interface identifier support is used for assigning well-known host-part addresses to nodes whilst still obtaining a global
network prefix from Router advertisements. The primary target for tokenized identifiers are server platforms where addresses are usually
manually configured, rather than using DHCPv6 or SLAAC. By using tokenized identifiers, hosts can still determine their network prefix by
use of SLAAC, but more readily be automatically renumbered should their network prefix change [1]. Tokenized IPv6 Identifiers are described
in the draft [1]: <draft-chown-6man-tokenised-ipv6-identifiers-02>.
ip token set - set an interface token
set the interface token to the kernel.
TOKEN the interface identifier token address.
dev DEV
the networking interface.
ip token del - delete an interface token
delete the interface token from the kernel.
dev DEV
the networking interface.
ip token get - get the interface token from the kernel
show a tokenized interface identifier of a particular networking device. Arguments: coincide with the arguments of ip token set but the
TOKEN must be left out.
ip token list - list all interface tokens
list all tokenized interface identifiers for the networking interfaces from the kernel.
SEE ALSO
ip(8)
AUTHOR
Manpage by Daniel Borkmann
iproute2 28 Mar 2013 IP-TOKEN(8)