Hi,
I have a problem with a server disconnecting from the network.
This is a SUN box with dual NIC's running Solaris 8.
We have a Nokia router that routes traffic but it's virtual address doesn't respond to pings. When the SUN box sends out a ping, if nothing comes back it will shut down... (5 Replies)
I have one 4GB, dual port HBA. Is each port rated for 4GB, or is it the whole HBA rated for 4GB?
Also, how do I determine which is port0 / port1 with "lscfg -vl fcs0" command. Thanks. (0 Replies)
Greetings Forumers!
I am running into an issue with multiple zones on an M5000 with 2 NICs. The NICs are on separate VLANs. These zones are using the 2 NICs to communicate with other systems but when they need to communicate with a zone on the same system, but different NIC, the application... (9 Replies)
All
I am at a loss with a VIO server running ios 2.2.0.10-FP-24 SP-01. The VIO server is fitted with two 8Gb PCI Express Dual Port FC Adapters. However when I run the lsnports command only two of the adapter ports show as capable:
$ lsnports
name physloc ... (4 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Hi,
From the man page, cfgmgr configures devices and optionally installs device software by running the programs specified in the Configuration Rules object class and it is not dependent on platform .
Are there any fundamental differences impacting the speed of cfgmgr on a stand-alone and... (5 Replies)
NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR.
How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a... (1 Reply)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT OSF1
cfgmgr_set_status
cfgmgr_set_status(9r)cfgmgr_set_status(9r)NAME
cfgmgr_set_status - General: Reports failure to the cfgmgr framework
SYNOPSIS
int cfgmgr_set_status(
char *driver_name );
ARGUMENTS
Specifies the name of the device driver for which you want to report an associated failure. This name is a string that matches the string
you specified for the entry_name item in the /etc/sysconfigtab database. Typically, third-party driver writers specify the driver name
(followed by a colon) in the sysconfigtab file fragment, which gets appended to the /etc/sysconfigtab database during the driver product
installation.
DESCRIPTION
The cfgmgr_set_status routine reports to the cfgmgr framework that a failure has occurred during static configuration. If the specified
device driver is in the static configuration state, it does not know that the configuration operation is complete until all register call-
back requests (routines) have successfully completed. Therefore, a device driver calls cfgmgr_set_status to report a possible failure dur-
ing static configuration to the cfgmgr framework.
Specifically, cfgmgr_set_status performs the following failure operations: Adjusts the state of the specified device driver Unconfigures
the specified device driver from the cfgmgr framework
The cfgmgr_set_status routine calls the device driver's configure routine at its CFG_OP_UNCONFIGURE entry point as part of these failure
operations. The code associated with the CFG_OP_UNCONFIGURE entry point is responsible for determining how to deallocate any allocated
resources during these failure operations.
The cfgmgr_set_status routine does not notify the operator of a configuration failure. Part of the code associated with the CFG_OP_UNCON-
FIGURE entry point could include an error logging operation to record the fact that a failure has occurred. The reason for doing this is
that the cfgmgr framework's task is to accomplish the unconfigure operation of a statically configured device driver.
You call the cfgmgr_set_status routine in the device driver's callback routine when the static configuration operation fails. You register
a callback routine by calling the register_callback routine.
RETURN VALUES
Upon successful completion, cfgmgr_set_status returns the value ESUCCESS. This success value indicates that cfgmgr_set_status adjusted the
state of the device driver and caused the cfgmgr framework to unconfigure the driver. Otherwise, cfgmgr_set_status returns one of the fol-
lowing error constants defined in /usr/sys/include/sys/sysconfig.h and /usr/sys/include/sys/errno.h: The device driver that you specified
in the driver_name argument does not exist. In this case, cfgmgr_set_status cannot adjust the state and unconfigure the device driver. The
device driver that you specified in the driver_name argument was not statically configured. The device driver that you specified in the
driver_name argument is not in the static configuration state.
EXAMPLES
See Writing Device Drivers: Tutorial for a code example of the cfgmgr_set_status interface.
SEE ALSO
Routines: cfgmgr_get_state(9r), register_callback(9r)cfgmgr_set_status(9r)