03-03-2009
No breakthrough even after touch /reconfigure the file......
10 More Discussions You Might Find Interesting
1. Solaris
hi after installation of sol 10 u 2 system started rebooting and when i tried to install solaris the system is giving:
panic/thread=cbacf800: BAD TRAP: type=e(#pf page fault) rp=fec38ae4 addr=458b247d occured in module "unix" due to an illegal access to a user address syncing file systems..... (2 Replies)
Discussion started by: nibiru78
2 Replies
2. Shell Programming and Scripting
Hello, the ls -d command to only list directories in a directory doesn't seem to work on Solaris and the man command says to use that combination: ls -d
Anyone have the same problem and find a resolve?
Thanks
BobK (9 Replies)
Discussion started by: bobk544
9 Replies
3. Solaris
I have a solaris 10 system configured using NetApp as its storage, and the file systems are already configured as you can see from the example below:
root@moneta # df -h
Filesystem size used avail capacity Mounted on
/dev/md/dsk/d0 9.8G 513M 9.3G 6% /
... (0 Replies)
Discussion started by: fretagi
0 Replies
4. Solaris
I have a solaris 10 system configured using NetApp as its storage, and the file systems are already configured as you can see from the example below:
root@moneta # df -h
Filesystem size used avail capacity Mounted on
/dev/md/dsk/d0 9.8G 513M 9.3G 6% /... (4 Replies)
Discussion started by: fretagi
4 Replies
5. UNIX for Dummies Questions & Answers
i'm trying to add disk to red hat , use fdisk -l but it doesn't recognize it
what should i do it to get it works? (3 Replies)
Discussion started by: prpkrk
3 Replies
6. Solaris
Good day.
I have a SUN Netra X4200 running on Solaris 10, with two disks in raid 1 configuration. HDD0 (c2t0d0) seems to have a problem but HDD1 (c2t1d0) is ok:
# for a in c2t0d0 c2t1d0 ; do raidctl -l $a; done
Volume Size Stripe Status Cache RAID
Sub ... (5 Replies)
Discussion started by: BRH
5 Replies
7. Solaris
Hi, one of my server won't boot. I restarted system while sysconfig configure was running. I can't boot into normal user mode. I always get error svc:/system/config-user:default is in maintenance mode and some lib exists with status 95.
I tried to boot into single user mode and to clear this... (6 Replies)
Discussion started by: solaris_user
6 Replies
8. Hardware
Hello,
I have a spare SUN server X4200 with a DC PSU (oracle part number 300-2186)
The PSU is the one in the photo
I was looking in the net about what cable i can order but i couldn't find anything that fit there :)
Any idea?
Thanks! (2 Replies)
Discussion started by: @dagio
2 Replies
9. UNIX for Advanced & Expert Users
Hello,
I have rebooted the RHEL VM but after rebooting the vm it not showing all the partition mounted on OS level, if i'll execute the fdisk -l command, then i'm able to see the same disk. below is the fdisk output :
# fdisk -l
Disk /dev/sda: 107.6 GB, 107639996416 bytes
255 heads, 63... (1 Reply)
Discussion started by: purushottamaher
1 Replies
10. Solaris
Hi Guys,
Could someone please share the dvd/cd that came with server Netra x4200 M2 since it is not more available in Oracle site? Or do you know where I can get that?
Thanks! (4 Replies)
Discussion started by: CristianS
4 Replies
LEARN ABOUT PLAN9
dpkg-reconfigure
DPKG-RECONFIGURE(8) Debconf DPKG-RECONFIGURE(8)
NAME
dpkg-reconfigure - reconfigure an already installed package
SYNOPSIS
dpkg-reconfigure [options] packages
DESCRIPTION
dpkg-reconfigure reconfigures packages after they have already been installed. Pass it the names of a package or packages to reconfigure.
It will ask configuration questions, much like when the package was first installed.
If you just want to see the current configuration of a package, see debconf-show(1) instead.
OPTIONS
-ftype, --frontend=type
Select the frontend to use. The default frontend can be permanently changed by:
dpkg-reconfigure debconf
Note that if you normally have debconf set to use the noninteractive frontend, dpkg-reconfigure will use the dialog frontend instead,
so you actually get to reconfigure the package.
-pvalue, --priority=value
Specify the minimum priority of question that will be displayed. dpkg-reconfigure normally shows low priority questions no matter what
your default priority is. See debconf(7) for a list.
--default-priority
Use whatever the default priority of question is, instead of forcing the priority to low.
-u, --unseen-only
By default, all questions are shown, even if they have already been answered. If this parameter is set though, only questions that have
not yet been seen will be asked.
--force
Force dpkg-reconfigure to reconfigure a package even if the package is in an inconsistent or broken state. Use with caution.
--no-reload
Prevent dpkg-reconfigure from reloading templates. Use with caution; this will prevent dpkg-reconfigure from repairing broken templates
databases. However, it may be useful in constrained environments where rewriting the templates database is expensive.
-h, --help
Display usage help.
SEE ALSO
debconf(7)
AUTHOR
Joey Hess <joeyh@debian.org>
2018-02-28 DPKG-RECONFIGURE(8)