03-03-2009
Try "cfgmgr -v - i /dev/cd0" with the installation media located in the cdrom device. It will force AIX to look for the appropriate drivers in the installation media.
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I have a problem with a server disconnecting from the network.
This is a SUN box with dual NIC's running Solaris 8.
We have a Nokia router that routes traffic but it's virtual address doesn't respond to pings. When the SUN box sends out a ping, if nothing comes back it will shut down... (5 Replies)
Discussion started by: m_smith
5 Replies
2. IP Networking
I have one 4GB, dual port HBA. Is each port rated for 4GB, or is it the whole HBA rated for 4GB?
Also, how do I determine which is port0 / port1 with "lscfg -vl fcs0" command. Thanks. (0 Replies)
Discussion started by: jwholey
0 Replies
3. Solaris
Greetings Forumers!
I am running into an issue with multiple zones on an M5000 with 2 NICs. The NICs are on separate VLANs. These zones are using the 2 NICs to communicate with other systems but when they need to communicate with a zone on the same system, but different NIC, the application... (9 Replies)
Discussion started by: bluescreen
9 Replies
4. AIX
All
I am at a loss with a VIO server running ios 2.2.0.10-FP-24 SP-01. The VIO server is fitted with two 8Gb PCI Express Dual Port FC Adapters. However when I run the lsnports command only two of the adapter ports show as capable:
$ lsnports
name physloc ... (4 Replies)
Discussion started by: johnf
4 Replies
5. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
6. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
7. AIX
Hi,
From the man page, cfgmgr configures devices and optionally installs device software by running the programs specified in the Configuration Rules object class and it is not dependent on platform .
Are there any fundamental differences impacting the speed of cfgmgr on a stand-alone and... (5 Replies)
Discussion started by: Sachin1987
5 Replies
8. AIX
NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR.
How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a... (1 Reply)
Discussion started by: gps1976
1 Replies
9. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
10. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
EJECT(1) BSD General Commands Manual EJECT(1)
NAME
eject -- eject a floppy disk, cdrom or tape
SYNOPSIS
eject [-fv] [-l | -L | -U] [-t device-type] [-d] device
eject -n
DESCRIPTION
The eject program ejects a medium from the specified device. It can also load a cdrom in the drive if this operation is supported by the
hardware. The device argument specifies a device either by its full path name (identified by a /dev/ prefix), or by one of the built-in
nicknames. If the medium contains a file system that is currently mounted, eject will attempt to unmount the file system before ejecting.
The following options are available:
-d Deprecated.
-f Force the eject operation without attempting to unmount any file systems first.
-l Load media in the drive (only supported for the cdrom device type).
-L Lock the media into the drive (but see BUGS below).
-n List the built-in nicknames on standard output.
-t device-type
Specify the device type. The argument must be one of diskette, floppy, cdrom, disk, or tape. This option is necessary when ejecting a
device for which no built-in knowledge is available.
-U Unlock the media from the drive.
-v Display some of the actions taken on standard output.
BUGS
Most disk drivers automatically lock the media on the first open and unlock it on the last close, making 'eject -L' almost useless, since
when it closes the device, it gets unlocked again.
BSD
October 6, 2001 BSD