03-03-2009
Can you see the LED on the disks blinking?
Can you touch a /reconfigure file, shutdown the system and the power up again?
If Im not wrong, you will need to reboot the system. I have faced similar problem before
10 More Discussions You Might Find Interesting
1. Solaris
hi after installation of sol 10 u 2 system started rebooting and when i tried to install solaris the system is giving:
panic/thread=cbacf800: BAD TRAP: type=e(#pf page fault) rp=fec38ae4 addr=458b247d occured in module "unix" due to an illegal access to a user address syncing file systems..... (2 Replies)
Discussion started by: nibiru78
2 Replies
2. Shell Programming and Scripting
Hello, the ls -d command to only list directories in a directory doesn't seem to work on Solaris and the man command says to use that combination: ls -d
Anyone have the same problem and find a resolve?
Thanks
BobK (9 Replies)
Discussion started by: bobk544
9 Replies
3. Solaris
I have a solaris 10 system configured using NetApp as its storage, and the file systems are already configured as you can see from the example below:
root@moneta # df -h
Filesystem size used avail capacity Mounted on
/dev/md/dsk/d0 9.8G 513M 9.3G 6% /
... (0 Replies)
Discussion started by: fretagi
0 Replies
4. Solaris
I have a solaris 10 system configured using NetApp as its storage, and the file systems are already configured as you can see from the example below:
root@moneta # df -h
Filesystem size used avail capacity Mounted on
/dev/md/dsk/d0 9.8G 513M 9.3G 6% /... (4 Replies)
Discussion started by: fretagi
4 Replies
5. UNIX for Dummies Questions & Answers
i'm trying to add disk to red hat , use fdisk -l but it doesn't recognize it
what should i do it to get it works? (3 Replies)
Discussion started by: prpkrk
3 Replies
6. Solaris
Good day.
I have a SUN Netra X4200 running on Solaris 10, with two disks in raid 1 configuration. HDD0 (c2t0d0) seems to have a problem but HDD1 (c2t1d0) is ok:
# for a in c2t0d0 c2t1d0 ; do raidctl -l $a; done
Volume Size Stripe Status Cache RAID
Sub ... (5 Replies)
Discussion started by: BRH
5 Replies
7. Solaris
Hi, one of my server won't boot. I restarted system while sysconfig configure was running. I can't boot into normal user mode. I always get error svc:/system/config-user:default is in maintenance mode and some lib exists with status 95.
I tried to boot into single user mode and to clear this... (6 Replies)
Discussion started by: solaris_user
6 Replies
8. Hardware
Hello,
I have a spare SUN server X4200 with a DC PSU (oracle part number 300-2186)
The PSU is the one in the photo
I was looking in the net about what cable i can order but i couldn't find anything that fit there :)
Any idea?
Thanks! (2 Replies)
Discussion started by: @dagio
2 Replies
9. UNIX for Advanced & Expert Users
Hello,
I have rebooted the RHEL VM but after rebooting the vm it not showing all the partition mounted on OS level, if i'll execute the fdisk -l command, then i'm able to see the same disk. below is the fdisk output :
# fdisk -l
Disk /dev/sda: 107.6 GB, 107639996416 bytes
255 heads, 63... (1 Reply)
Discussion started by: purushottamaher
1 Replies
10. Solaris
Hi Guys,
Could someone please share the dvd/cd that came with server Netra x4200 M2 since it is not more available in Oracle site? Or do you know where I can get that?
Thanks! (4 Replies)
Discussion started by: CristianS
4 Replies
HALT(8) Linux System Administrator's Manual HALT(8)
NAME
halt, reboot, poweroff - stop the system.
SYNOPSIS
/sbin/halt [-n] [-w] [-d] [-f] [-i] [-p] [-h]
/sbin/reboot [-n] [-w] [-d] [-f] [-i]
/sbin/poweroff [-n] [-w] [-d] [-f] [-i] [-h]
DESCRIPTION
halt notes that the system is being brought down in the file /var/log/wtmp, and then either tells the kernel to halt, reboot or power-off
the system.
If halt or reboot is called when the system is not in runlevel 0 or 6, in other words when it's running normally, shutdown will be invoked
instead (with the -h or -r flag). For more info see the shutdown(8) manpage.
The rest of this manpage describes the behaviour in runlevels 0 and 6, that is when the systems shutdown scripts are being run.
OPTIONS
-n Don't sync before reboot or halt. Note that the kernel and storage drivers may still sync. This implies -d.
-w Don't actually reboot or halt but only write the wtmp record (in the /var/log/wtmp file).
-d Don't write the wtmp record.
-f Force halt or reboot, don't call shutdown(8).
-i Shut down all network interfaces just before halt or reboot.
-h Put all hard drives on the system in stand-by mode just before halt or power-off.
-p When halting the system, switch off the power. This is the default when halt is called as poweroff.
DIAGNOSTICS
If you're not the superuser, you will get the message `must be superuser'.
NOTES
Under older sysvinit releases , reboot and halt should never be called directly. From release 2.74 on halt and reboot invoke shutdown(8) if
the system is not in runlevel 0 or 6. This means that if halt or reboot cannot find out the current runlevel (for example, when
/var/run/utmp hasn't been initialized correctly) shutdown will be called, which might not be what you want. Use the -f flag if you want to
do a hard halt or reboot.
The -h flag puts all hard disks in standby mode just before halt or power-off. Right now this is only implemented for IDE drives. A side
effect of putting the drive in stand-by mode is that the write cache on the disk is flushed. This is important for IDE drives, since the
kernel doesn't flush the write cache itself before power-off.
The halt program uses /proc/ide/hd* to find all IDE disk devices, which means that /proc needs to be mounted when halt or poweroff is
called or the -h switch will do nothing.
AUTHOR
Miquel van Smoorenburg, miquels@cistron.nl
SEE ALSO
shutdown(8), init(8)
Nov 6, 2001 HALT(8)