03-03-2009
x4200 solaris doesn't see new disk
I got two 2.5" disk for a x4200 and put it in.
Just same these disk were, I remember doing this in the past, working..
Now when I put in the disk and run 'devfsadm' and also check with 'cfgadm -a', that disk doesn't seem to show up.
When I pull out the disk I see this in the logs:
Mar 2 13:52:34 chsys064 genunix: [ID 935449 kern.info] ATA DMA off: disabled. Control with "atapi-cd-dma-enabled" pr
operty
Mar 2 13:52:34 chsys064 genunix: [ID 882269 kern.info] PIO mode 4 selected
Mar 3 08:12:02 chsys064 scsi: [ID 107833 kern.notice] /pci@7b,0/pci1022,7458@11/pci1000,3060@2 (mpt4):
Mar 3 08:12:02 chsys064 Phydisk disk 2 does not belong to any volume
Mar 3 08:12:02 chsys064 scsi: [ID 107833 kern.notice] /pci@7b,0/pci1022,7458@11/pci1000,3060@2 (mpt4):
Mar 3 08:12:02 chsys064 Phydisk disk 7 does not belong to any volume
How can I get it to show up? No new /dev/dsk/* entries are being created. format also doesn't seem to show the disk.
10 More Discussions You Might Find Interesting
1. Solaris
hi after installation of sol 10 u 2 system started rebooting and when i tried to install solaris the system is giving:
panic/thread=cbacf800: BAD TRAP: type=e(#pf page fault) rp=fec38ae4 addr=458b247d occured in module "unix" due to an illegal access to a user address syncing file systems..... (2 Replies)
Discussion started by: nibiru78
2 Replies
2. Shell Programming and Scripting
Hello, the ls -d command to only list directories in a directory doesn't seem to work on Solaris and the man command says to use that combination: ls -d
Anyone have the same problem and find a resolve?
Thanks
BobK (9 Replies)
Discussion started by: bobk544
9 Replies
3. Solaris
I have a solaris 10 system configured using NetApp as its storage, and the file systems are already configured as you can see from the example below:
root@moneta # df -h
Filesystem size used avail capacity Mounted on
/dev/md/dsk/d0 9.8G 513M 9.3G 6% /
... (0 Replies)
Discussion started by: fretagi
0 Replies
4. Solaris
I have a solaris 10 system configured using NetApp as its storage, and the file systems are already configured as you can see from the example below:
root@moneta # df -h
Filesystem size used avail capacity Mounted on
/dev/md/dsk/d0 9.8G 513M 9.3G 6% /... (4 Replies)
Discussion started by: fretagi
4 Replies
5. UNIX for Dummies Questions & Answers
i'm trying to add disk to red hat , use fdisk -l but it doesn't recognize it
what should i do it to get it works? (3 Replies)
Discussion started by: prpkrk
3 Replies
6. Solaris
Good day.
I have a SUN Netra X4200 running on Solaris 10, with two disks in raid 1 configuration. HDD0 (c2t0d0) seems to have a problem but HDD1 (c2t1d0) is ok:
# for a in c2t0d0 c2t1d0 ; do raidctl -l $a; done
Volume Size Stripe Status Cache RAID
Sub ... (5 Replies)
Discussion started by: BRH
5 Replies
7. Solaris
Hi, one of my server won't boot. I restarted system while sysconfig configure was running. I can't boot into normal user mode. I always get error svc:/system/config-user:default is in maintenance mode and some lib exists with status 95.
I tried to boot into single user mode and to clear this... (6 Replies)
Discussion started by: solaris_user
6 Replies
8. Hardware
Hello,
I have a spare SUN server X4200 with a DC PSU (oracle part number 300-2186)
The PSU is the one in the photo
I was looking in the net about what cable i can order but i couldn't find anything that fit there :)
Any idea?
Thanks! (2 Replies)
Discussion started by: @dagio
2 Replies
9. UNIX for Advanced & Expert Users
Hello,
I have rebooted the RHEL VM but after rebooting the vm it not showing all the partition mounted on OS level, if i'll execute the fdisk -l command, then i'm able to see the same disk. below is the fdisk output :
# fdisk -l
Disk /dev/sda: 107.6 GB, 107639996416 bytes
255 heads, 63... (1 Reply)
Discussion started by: purushottamaher
1 Replies
10. Solaris
Hi Guys,
Could someone please share the dvd/cd that came with server Netra x4200 M2 since it is not more available in Oracle site? Or do you know where I can get that?
Thanks! (4 Replies)
Discussion started by: CristianS
4 Replies
pfto(7) Miscellaneous Information Manual pfto(7)
NAME
pfto - Powerfail Timeout
DESCRIPTION
HP-UX SCSI disk device drivers have a timeout facility that detects non-responding disks. VxVM uses this mechanism in its Powerfail Time-
out (pfto) feature. You can specify a timeout value for individual VxVM disks using the vxdisk command (see the EXAMPLES section below).
If a disk fails to respond in the specified timeout period, the driver receives a timer interrupt.
pfto values are persistent across reboots, that is, after the pfto value is set, it remains in effect until you explicitly change it. If
dynamic multipathing is enabled, the pfto value set on a disk applies to each path of a multipath disk device.
The pfto value is in seconds. If pfto is not specified, or is zero, the timeout period is 30 seconds. Both the vxdisk and vxprint commands
display the current pfto value for a disk.
EXAMPLES
Use the following command to set the value of pfto to 30 seconds on disk01:
vxdisk -g rootdg set disk01 pfto=30
Use either of the following commands to display the pfto value on the VxVM disk disk01:
vxdisk list disk01
vxprint -l disk01
EXIT CODES
Setting the pfto value on a non-VxVM disk returns an error.
SEE ALSO
vxdisk(1M), vxprint(1M)
VxVM 5.0.31.1 24 Mar 2008 pfto(7)