03-03-2009
x4200 solaris doesn't see new disk
I got two 2.5" disk for a x4200 and put it in.
Just same these disk were, I remember doing this in the past, working..
Now when I put in the disk and run 'devfsadm' and also check with 'cfgadm -a', that disk doesn't seem to show up.
When I pull out the disk I see this in the logs:
Mar 2 13:52:34 chsys064 genunix: [ID 935449 kern.info] ATA DMA off: disabled. Control with "atapi-cd-dma-enabled" pr
operty
Mar 2 13:52:34 chsys064 genunix: [ID 882269 kern.info] PIO mode 4 selected
Mar 3 08:12:02 chsys064 scsi: [ID 107833 kern.notice] /pci@7b,0/pci1022,7458@11/pci1000,3060@2 (mpt4):
Mar 3 08:12:02 chsys064 Phydisk disk 2 does not belong to any volume
Mar 3 08:12:02 chsys064 scsi: [ID 107833 kern.notice] /pci@7b,0/pci1022,7458@11/pci1000,3060@2 (mpt4):
Mar 3 08:12:02 chsys064 Phydisk disk 7 does not belong to any volume
How can I get it to show up? No new /dev/dsk/* entries are being created. format also doesn't seem to show the disk.
10 More Discussions You Might Find Interesting
1. Solaris
hi after installation of sol 10 u 2 system started rebooting and when i tried to install solaris the system is giving:
panic/thread=cbacf800: BAD TRAP: type=e(#pf page fault) rp=fec38ae4 addr=458b247d occured in module "unix" due to an illegal access to a user address syncing file systems..... (2 Replies)
Discussion started by: nibiru78
2 Replies
2. Shell Programming and Scripting
Hello, the ls -d command to only list directories in a directory doesn't seem to work on Solaris and the man command says to use that combination: ls -d
Anyone have the same problem and find a resolve?
Thanks
BobK (9 Replies)
Discussion started by: bobk544
9 Replies
3. Solaris
I have a solaris 10 system configured using NetApp as its storage, and the file systems are already configured as you can see from the example below:
root@moneta # df -h
Filesystem size used avail capacity Mounted on
/dev/md/dsk/d0 9.8G 513M 9.3G 6% /
... (0 Replies)
Discussion started by: fretagi
0 Replies
4. Solaris
I have a solaris 10 system configured using NetApp as its storage, and the file systems are already configured as you can see from the example below:
root@moneta # df -h
Filesystem size used avail capacity Mounted on
/dev/md/dsk/d0 9.8G 513M 9.3G 6% /... (4 Replies)
Discussion started by: fretagi
4 Replies
5. UNIX for Dummies Questions & Answers
i'm trying to add disk to red hat , use fdisk -l but it doesn't recognize it
what should i do it to get it works? (3 Replies)
Discussion started by: prpkrk
3 Replies
6. Solaris
Good day.
I have a SUN Netra X4200 running on Solaris 10, with two disks in raid 1 configuration. HDD0 (c2t0d0) seems to have a problem but HDD1 (c2t1d0) is ok:
# for a in c2t0d0 c2t1d0 ; do raidctl -l $a; done
Volume Size Stripe Status Cache RAID
Sub ... (5 Replies)
Discussion started by: BRH
5 Replies
7. Solaris
Hi, one of my server won't boot. I restarted system while sysconfig configure was running. I can't boot into normal user mode. I always get error svc:/system/config-user:default is in maintenance mode and some lib exists with status 95.
I tried to boot into single user mode and to clear this... (6 Replies)
Discussion started by: solaris_user
6 Replies
8. Hardware
Hello,
I have a spare SUN server X4200 with a DC PSU (oracle part number 300-2186)
The PSU is the one in the photo
I was looking in the net about what cable i can order but i couldn't find anything that fit there :)
Any idea?
Thanks! (2 Replies)
Discussion started by: @dagio
2 Replies
9. UNIX for Advanced & Expert Users
Hello,
I have rebooted the RHEL VM but after rebooting the vm it not showing all the partition mounted on OS level, if i'll execute the fdisk -l command, then i'm able to see the same disk. below is the fdisk output :
# fdisk -l
Disk /dev/sda: 107.6 GB, 107639996416 bytes
255 heads, 63... (1 Reply)
Discussion started by: purushottamaher
1 Replies
10. Solaris
Hi Guys,
Could someone please share the dvd/cd that came with server Netra x4200 M2 since it is not more available in Oracle site? Or do you know where I can get that?
Thanks! (4 Replies)
Discussion started by: CristianS
4 Replies
LEARN ABOUT HPUX
vxreattach
vxreattach(1M) vxreattach(1M)
NAME
vxreattach - reattach disk drives that have once again become accessible
SYNOPSIS
/etc/vx/bin/vxreattach [-br ] [accessname...]
/etc/vx/bin/vxreattach -c accessname
DESCRIPTION
The vxreattach utility reattaches disks to the disk group they were in and retains the same media name.
This operation may be necessary if a disk has a transient failure, or if Veritas Volume Manager (VxVM) starts with some disk drivers
unloaded and unloadable. Disks then enter the failed state. If the problem is fixed, vxreattach may be able to reattach the disks without
plexes being flagged as stale, as long as the reattach happens before any volumes on the disk are started.
vxreattach tries to find a disk in the same disk group with the same disk ID for the disk(s) to be reattached. The reattach operation may
fail even after finding the disk with the matching disk ID if the original cause (or some other cause) for the disk failure still exists.
vxreattach is usually invoked by vxdiskadm when performing disk recovery. It is not intended to be run directly by an administrator.
OPTIONS
-b Performs the reattach operation in the background.
-c Checks if a reattach is possible. No operation is performed, but the name of the disk group and disk media name at which the
disk can be reattached is displayed.
-r Tries to recover stale plexes of any volumes on the failed disk. It does this by calling vxrecover.
EXIT CODES
A zero exit status is returned if the reattach is performed; non-zero is returned otherwise.
See vxintro(1M) for a list of standard exit codes.
EXAMPLES
Check if reattachment of disk c1t2d0 is possible:
/etc/vx/bin/vxreattach -c c1t2d0
If reattachment is possible, vxreattach returns with an exit status of 0 and displays the disk group name and disk media name. If reat-
tachment is not possible, vxreattach returns an exit status of 2 and displays an error.
Attempt to reattach the disk in the foreground and try to recover stale plexes of any volumes on the disk:
/etc/vx/bin/vxreattach -r c1t2d0
If the reattachment is successful, vxreattach returns an exit status of 0. Otherwise, if an error occurs, vxreattach returns a non-zero
exit code as defined on vxintro(1M).
FILES
/etc/default/vxplex Standard defaults file that can be used to determine whether FastResync is used when attaching plexes. See vxplex(1M)
for details.
SEE ALSO
vxdiskadm(1M), vxintro(1M), vxplex(1M), vxrecover(1M)
VxVM 5.0.31.1 24 Mar 2008 vxreattach(1M)