03-02-2009
There's a number of listings if you search on the error cfgmgr: 0514-621 WARNING. Is this a card you purchased with the system from IBM or an add on? Do you know the card's make/mfgr. ID?
Cheers,
Keith
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I have a problem with a server disconnecting from the network.
This is a SUN box with dual NIC's running Solaris 8.
We have a Nokia router that routes traffic but it's virtual address doesn't respond to pings. When the SUN box sends out a ping, if nothing comes back it will shut down... (5 Replies)
Discussion started by: m_smith
5 Replies
2. IP Networking
I have one 4GB, dual port HBA. Is each port rated for 4GB, or is it the whole HBA rated for 4GB?
Also, how do I determine which is port0 / port1 with "lscfg -vl fcs0" command. Thanks. (0 Replies)
Discussion started by: jwholey
0 Replies
3. Solaris
Greetings Forumers!
I am running into an issue with multiple zones on an M5000 with 2 NICs. The NICs are on separate VLANs. These zones are using the 2 NICs to communicate with other systems but when they need to communicate with a zone on the same system, but different NIC, the application... (9 Replies)
Discussion started by: bluescreen
9 Replies
4. AIX
All
I am at a loss with a VIO server running ios 2.2.0.10-FP-24 SP-01. The VIO server is fitted with two 8Gb PCI Express Dual Port FC Adapters. However when I run the lsnports command only two of the adapter ports show as capable:
$ lsnports
name physloc ... (4 Replies)
Discussion started by: johnf
4 Replies
5. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
6. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
7. AIX
Hi,
From the man page, cfgmgr configures devices and optionally installs device software by running the programs specified in the Configuration Rules object class and it is not dependent on platform .
Are there any fundamental differences impacting the speed of cfgmgr on a stand-alone and... (5 Replies)
Discussion started by: Sachin1987
5 Replies
8. AIX
NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR.
How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a... (1 Reply)
Discussion started by: gps1976
1 Replies
9. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
10. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
CARD(1) FSF CARD(1)
NAME
card - print reference card of program options
SYNOPSIS
card [OPTION]... PROGRAM...
DESCRIPTION
Print a reference card of the PROGRAMs thanks to their inline help.
OPTIONS
-h, --help
display this help and exit
-v, --version
display version information and exit
-o, --output=FILE
save the output in FILE
-l, --language=LL
print the help in the language LL (default: English)
--command=CMD
perform pretty-printing on the output of CMD (e.g. --command='netscape -help')
Options for a2ps are given after `--', for instance
$ card -lfr a2ps -- -Pdisplay -4
News, updates and documentation: http://www.inf.enst.fr/~demaille/a2ps/
AUTHOR
Written by Akim Demaille.
REPORTING BUGS
Report bugs to <bug-a2ps@gnu.org>.
COPYRIGHT
Copyright (C) 1997-99 Akim Demaille, Miguel Santana
This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICU-
LAR PURPOSE.
SEE ALSO
a2ps(1), card(1), fixps(1), pdiff(1), psset(1), texi2dvi4a2ps(1).
The full documentation for card is maintained as a Texinfo manual. If the info and card programs are properly installed at your site, the
command
info card
should give you access to the complete manual.
card 1.3 (GNU a2ps 4.14) December 2007 CARD(1)