Adding Loopback Interface Post: 302292673

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Adding an interface to solaris?

I have a quad ethernet card in my sun box, and only 3 of them are visable when I "ifconfig -a". How do I activate the the 4th one? I think it is solaris 5.6. Thanks. Marc

2. UNIX for Advanced & Expert Users

Loopback Interface...Vanished???

Recently I noticed that my internet connection would not work correctly-although connected domain names could not be resolved. My resolv.conf file was fine since it is configured every time I dial up. a closer inspection showed that my loopback interface had disappearerd! Any ideas why would this...

3. HP-UX

Adding virtual Interface on HP UX

Hello all, I want to add a new virtual interface on HP-UX B.11.11 U 9000/800 box. I know that ifconfig can be used to add the Virtual interface. BUt i do not know the exact syntax. it some times gives plumb error if i try to add # ifconfig vif0 10.1.10.1 up plumb error: No such file...

4. Red Hat

Configure floating IP on loopback interface

Hi All, I need to configure a floating IP on loopback interface of two servers (RHEL 5.4). After configuring, I'm not able to ping to that IP from a different server. I fail to understand what is missing here. I have done similar configuration in another environment & it works fine. Plz help....

5. Solaris

Network interface down after adding static route

Please , I have a problem I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline. The system is in cluster mode (3.2) route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51 ------------------- lo0:...

6. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI...

7. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you

8. Linux

Loopback interface doen't appear

Hi all, i have a problem with (Network in Linux) .. my issue with a HW appliance has openfiler 2.3 and is used for File Sharing using samba .. the problem is when i try to list all configured network interfaces using ifconfig -a .. i can't see the loopback interface, Although the file...

9. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

LEARN ABOUT OSF1

install-solaris

install-solaris(1M)													       install-solaris(1M)

NAME

       install-solaris - install the Solaris operating system

SYNOPSIS

       install-solaris

       install-solaris	invokes  the  Solaris  Install	program. Depending on graphical capability and available memory at the time of invocation,
       install-solaris invokes either a text-based installer or a graphical installer.

       The following minimum requirements for physical memory dictate which features are available during installation:

       For SPARC machines:

       128 MB

	   Minimum physical memory for all installation types

       128 MB

	   Minimum physical memory required for windowing system

       384 MB

	   Minimum physical memory required for graphical-based installation

       For x86 machines:

       256 MB

	   Minimum physical memory for all installation types

       256 MB

	   Minimum physical memory required for windowing system

       512 MB

	   Minimum physical memory required for graphical-based installation

       In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number  of  fea-
       tures available.

       install-solaris	exists	only  on  the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the  for more
       details.

       install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
       installation media. Refer to the  for disk space requirements.

       Refer to the  for more information on the various menus and selections.

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWcdrom  (Solaris instal-  |
       |			     |lation media)		   |
       +-----------------------------+-----------------------------+
       |Interface Stability	     |Evolving			   |
       +-----------------------------+-----------------------------+

       pkginfo(1), install(1M), pkgadd(1M), attributes(5)

       It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.

								    23 Sep 2005 					       install-solaris(1M)