02-27-2009
Hi,
Thanks a lot for your quick response .These are very much helpful for me but I want some more information about the keyboard ,mouse and monitor details like manufacturer,serial number etc..
Thanks in advance.
9 More Discussions You Might Find Interesting
1. Solaris
I'm trying to mirror 2 eide disks on a solaris 10 x86 system.
Im trying to use the prtvtoc | fmthard command to mirror the vtoc.
How do they represent the entire disk like in solaris 9 (c0t0d0s2 = entire device)
0. c0d0 <DEFAULT cyl 26497 alt 2 hd 16 sec 63>
... (1 Reply)
Discussion started by: BG_JrAdmin
1 Replies
2. Solaris
i want to use the devfsadm command and understand its function (3 Replies)
Discussion started by: bondoq
3 Replies
3. UNIX for Dummies Questions & Answers
I've been looking in my /dev directory for my available devices to set up a printer and was expecting to see some lp or lpr devices using Solaris 8, but I do not see them so I'm a little confused?
Any help would be greatly appreciated. (2 Replies)
Discussion started by: jroglass
2 Replies
4. Solaris
I want to configure my Network card. On solaris 9 i386.
How to know the good Network device. I use prtconf
to display the device list. I'm searching the device name.
Like ifconfig device_name plumb
thanks you (2 Replies)
Discussion started by: simquest
2 Replies
5. Solaris
Hi all,
I wanted to know the solaris way of interpreting devices?
I mean i understand all those c0t0....stuff but when i start mounting devices , most of the times i get either a I/O error or it says that the directory does not exist.
eg:
I have a external usb hub to which i have connected... (1 Reply)
Discussion started by: wrapster
1 Replies
6. Solaris
Hello all,
I'm having issue with trying to add device resource to my zone from the global zone.
I did the following
zoncfg -x larryase
add device
set match="/dev/tty*"
end
I get device already set, but in me zone I don't see the device.
Is there a "reboot -- r" command for zones? or... (0 Replies)
Discussion started by: larryase
0 Replies
7. Solaris
Could anyone tell me where I can obtain Solaris 10 10/09 drivers for these divices listed below. I have looked in the OpenSolaris forums but I have not had any luck.
Device Vendor Device Name
Network Atheros AR928X Wireless Network Adapter (PCI-Express)
Storage Intel 82801 SATA... (4 Replies)
Discussion started by: Tenyhwa
4 Replies
8. Solaris
Hi ,
I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
Discussion started by: naveen448
0 Replies
9. Solaris
Hi, Any help would be appreciated, when I attempt to install either OpenSolaris or Solaris 11 the install hangs right after the copyright where normally it would be "configuring devices" . If it is SOL 11 it just hangs if it is OpenSolaris it starts spitting out the following:
WARNING: hubdi:... (0 Replies)
Discussion started by: jk121960
0 Replies
dc(4) Kernel Interfaces Manual dc(4)
Name
dc - serial line/mouse/keyboard
Syntax
device dc0 at ibus? vector dcintr
Description
The serial line controller provides four ports, with modem control on two of the ports. The DECstation 3100 and DECstation 2100 only pro-
vide partial modem control. The DECstation 5000 provides full modem control. The ports are used as follows:
Port Usage
0 Graphics device keyboard at 4800 BPS
1 Mouse or tablet at 4800 BPS
2 Communications port 1 (w/modem control)/local terminal
3 Communications port 2 (w/modem control)/local terminal
Each communication port from the serial line controller behaves as described in and can be set to run at any of 16 speeds. For the encod-
ing, see
When a graphics device is not being used as the system console, communications port 2 becomes the system console. In this configuration,
the port can only be used at 9600 BPS and no modem control is supported.
The serial line driver operates in interrupt-per-character mode (all pending characters are flushed from the silo on each interrupt).
Restrictions
Speed must be set to 9600 BPS on the console port and 4800 BPS on ports used by graphics devices. The serial line driver enforces this
restriction; that is, changing speeds with the command may not always work on these ports.
Files
console terminal
local terminal
local terminal
See Also
console(4), devio(4), tty(4), ttys(5), MAKEDEV(8)
RISC dc(4)