Reg. NIC card Post: 302291509

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

No NIC Card?

Hello Everyone, While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use. There is no output for dmesg|grep eth. Does that mean that mandrake...

2. HP-UX

configuring nic card

using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ?

3. Linux

Howto Detect New Nic Card

Hi PPL! I have P-IV processor, with on-board NIC card. I have added one more NIC card for domestic use. My kudzu does not recognise the newly added PCMCIA NIC card. How to go about this one? Suggest PEnguin

4. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks

5. Solaris

Reg- eth0,eth1 (ethernet card)

Hi Guys, I am working as a L-1 support and i want to know that are the precaution need to take on eth0(Ethernet card) i heard on production server it is very much important, what are the steps need to observe on this tickets.

6. Solaris

NIC card repetative Failover

I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2 When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously. Following are the message log. ifmsdb1 in.mpathd: NIC failure detected...

7. Linux

changing speed of NIC Card in linux

Hi, I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0 and my requirement is 100mbps full duplex. Regards, Manoj

8. Linux

How to check which NIC Card is used for backups?

I have a linux box with 2 nic cards on it one for prod and one for backup. My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion.

9. HP-UX

NIC card issue

Hi, Someone asked me the below. If the box has multiple NIC cards, try to run a test with interface address specified as shown below $ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress> How can I now find out if my box has multiple NIC cards and how can I...

10. Red Hat

Finding speed of NIC Card

Hi, I would like to know how to find out ACTUAL speed of NIC Card. I have used the command ethtool eth0, it is showing supported modes, but what is acutal speed ? how to find out?

LEARN ABOUT DEBIAN

install-solaris

install-solaris(1M)													       install-solaris(1M)

NAME

       install-solaris - install the Solaris operating system

SYNOPSIS

       install-solaris

       install-solaris	invokes  the  Solaris  Install	program. Depending on graphical capability and available memory at the time of invocation,
       install-solaris invokes either a text-based installer or a graphical installer.

       The following minimum requirements for physical memory dictate which features are available during installation:

       For SPARC machines:

       128 MB

	   Minimum physical memory for all installation types

       128 MB

	   Minimum physical memory required for windowing system

       384 MB

	   Minimum physical memory required for graphical-based installation

       For x86 machines:

       256 MB

	   Minimum physical memory for all installation types

       256 MB

	   Minimum physical memory required for windowing system

       512 MB

	   Minimum physical memory required for graphical-based installation

       In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number  of  fea-
       tures available.

       install-solaris	exists	only  on  the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the  for more
       details.

       install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
       installation media. Refer to the  for disk space requirements.

       Refer to the  for more information on the various menus and selections.

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWcdrom  (Solaris instal-  |
       |			     |lation media)		   |
       +-----------------------------+-----------------------------+
       |Interface Stability	     |Evolving			   |
       +-----------------------------+-----------------------------+

       pkginfo(1), install(1M), pkgadd(1M), attributes(5)

       It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.

								    23 Sep 2005 					       install-solaris(1M)