Hi,
I want to split before reading the complete line as the line is very big and its throwing out of memory. can you suggest.
when i say
#cat $inputFile | while read eachLine
and use the eachLine to split its throwing out of memory as the line size is more than 10000000 characters.
Can you... (1 Reply)
Dear All,
I want to split single line into two line or three lines wherever “|” separated values comes using
Input line
test,DEMTEMPUT20100404010012,,,,,,,,|0070086|0070087,
output shoule be
test,DEMTEMPUT20100404010012,,,,,,,,0070086,
test,DEMTEMPUT20100404010012,,,,,,,,0070087, (14 Replies)
Hi,
I need help to split lines from a file into multiple files.
my input look like this:
13
23 45 45 6 7
33 44 55 66 7
13
34 5 6 7 87
45 7 8 8 9
13
44 55 66 77 8
44 66 88 99 6
I want to split every 3 lines from this file to be written to individual files. (3 Replies)
I am attempting to replace positions 44-46 with YYY if positions 48-50 = XXX.
awk -F "" '{if (substr($0,48,3)=="XXX") $44="YYY"}1' OFS="" $filename > $tempfile
But this is not working, 44-46 is still spaces in my tempfile instead of YYY. Any suggestions would be greatly appreciated. (9 Replies)
I guess this has a simple solution but can't figure out now.
having:
x="H:a:b:c"
to get H:
echo $x|awk -F: {'print $1'}
how can I put REST of line in another one? i.e.
echo $rest
a:b:c
thanks
---------- Post updated at 08:58 PM ---------- Previous update was at... (5 Replies)
Hi, I am trying to use an awk command to replace specific character positions on a line beginning with 80 with contents of another file.
The line beginning with 80 in file1 is as follows:
I want to replace the 000000000178800 (positions 34 - 49) on this file with the contents of... (2 Replies)
Hi All,
Hope you guys had a wonderful weekend
I have a scenario where in which I have to read a file line by line
and check for few words before redirecting to a file
I have searched the forum but,either those answers dint work (perhaps because of my wrong under standing of how IFS... (6 Replies)
Hi All
Is there a way to export every line into new txt file where by the title of each txt output are same as the line ?
I have this txt files containing names:
Kandra Vanhooser
Rhona Menefee
Reynaldo Hutt
Houston Rafferty
Charmaine Lord
Albertine Poucher
Juana Maes
Mitch Lobel... (2 Replies)
I have a very long line in a file separated by "|" delimiter like below. Due to the length of the line, I find it very difficult to read to find a match line.
file = temp.txt
word 1| word 2 | word 3|....
I would like to read the file temp.txt and print out all words line by line like... (1 Reply)
Discussion started by: boldnbeautiful
1 Replies
LEARN ABOUT OPENDARWIN
cut
CUT(1) BSD General Commands Manual CUT(1)NAME
cut -- select portions of each line of a file
SYNOPSIS
cut -b list [-n] [file ...]
cut -c list [file ...]
cut -f list [-d delim] [-s] [file ...]
DESCRIPTION
The cut utility selects portions of each line (as specified by list) from each file and writes them to the standard output. If no file argu-
ments are specified, or a file argument is a single dash ('-'), cut reads from from the standard input. The items specified by list can be
in terms of column position or in terms of fields delimited by a special character. Column numbering starts from 1.
The list option argument is a comma or whitespace separated set of increasing numbers and/or number ranges. Number ranges consist of a num-
ber, a dash ('-'), and a second number and select the fields or columns from the first number to the second, inclusive. Numbers or number
ranges may be preceded by a dash, which selects all fields or columns from 1 to the first number. Numbers or number ranges may be followed
by a dash, which selects all fields or columns from the last number to the end of the line. Numbers and number ranges may be repeated, over-
lapping, and in any order. It is not an error to select fields or columns not present in the input line.
The options are as follows:
-b list
The list specifies byte positions.
-c list
The list specifies character positions.
-d delim
Use the first character of delim as the field delimiter character instead of the tab character.
-f list
The list specifies fields, delimited in the input by a single tab character. Output fields are separated by a single tab character.
-n Do not split multi-byte characters.
-s Suppress lines with no field delimiter characters. Unless specified, lines with no delimiters are passed through unmodified.
ENVIRONMENT
The LANG, LC_ALL and LC_CTYPE environment variables affect the execution of cut if the -n option is specified. Their effect is described in
environ(7).
EXAMPLES
Extract users' login names and shells from the system passwd(5) file as ``name:shell'' pairs:
cut -d : -f 1,7 /etc/passwd
Show the names and login times of the currently logged in users:
who | cut -c 1-16,26-38
DIAGNOSTICS
The cut utility exits 0 on success, and >0 if an error occurs.
SEE ALSO paste(1)STANDARDS
The cut utility conforms to IEEE Std 1003.2-1992 (``POSIX.2'').
HISTORY
A cut command appeared in AT&T System III UNIX.
BUGS
The -c option is a synonym for the -b option, which causes incorrect behaviour in locales that support multibyte characters.
When operating on fields (-f option is specified), cut does not recognise multibyte characters, and the delim character is recognised in the
middle of multibyte sequences.
BSD June 6, 1993 BSD