Sponsored Content
Operating Systems Solaris IPMP on 2 physical interfaces Post 302287836 by robsonde on Sunday 15th of February 2009 10:48:21 PM
Old 02-15-2009
With two Interfaces
setup your interfaces like this......

/etc/hostname.ce0
192.168.10.10 netmask + broadcast + group ipmp0 up

/etc/hostname.ce1
group ipmp0 up

# ifconfig -a
ce0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 4
inet 192.168.10.10 netmask ffffff00 broadcast 192.168.10.255
groupname ipmp0
ether 0:3:ba:93:90:fc
ce1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 5
inet 0.0.0.0 netmask ff000000 broadcast 0.255.255.255
groupname ipmp0
ether 0:3:ba:93:91:35


NOTE: you must set local MAC in the nvram
this is driven by link based fault dection, you don't need any extra IP address.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

physical volume and physical disk.

Hello, I need explanations about physical disks and physical volumes. What is the difference between these 2 things? In fact, i am trying to understand what the AIX lspv2command does. Thank you in advance. (2 Replies)
Discussion started by: VeroL
2 Replies

2. UNIX for Dummies Questions & Answers

Physical volume- no free physical partitions

I was in smit, checking on disc space, etc. and it appears that one of our physical volumes that is part of a large volume group, has no free physical partitions. The server is running AIX 5.1. What would be the advisable step to take in this instance? (9 Replies)
Discussion started by: markper
9 Replies

3. Solaris

Ipmp

Hi All, Kindly help me in configuring IPMP or guid me to some link, tried goggling however no luck. Thanks in anticipation (1 Reply)
Discussion started by: kumarmani
1 Replies

4. Solaris

IPMP Configuration

Hi all, Currently i got a server which had two interface. I had study the <SystemAdministration Guide: IP> but still donno what is the correct step to configure it. Can u all help me on it? thanks # ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index... (6 Replies)
Discussion started by: SmartAntz
6 Replies

5. AIX

Maximum Limit of HMC to handle Physical Power Virtualization Physical Machine

Hello All, Can anybody please tell me what is the maximum limit of Physical IBM Power Machine which can be handled by single HMC at a single point of time? Thanks, Jenish (1 Reply)
Discussion started by: jenish_shah
1 Replies

6. Solaris

list of physical net interfaces

hi, Can I listdown all available net interfaces on my system like SF4800 or Netra440. I know there are 4 port physically present but I can't see or list them using either sysdef -v prtconf -vp prtdiag -v dladm kstat may be I'm missing switched on these or may some other command... (8 Replies)
Discussion started by: busyboy
8 Replies

7. Solaris

svc:/network/physical:default: Method "/lib/svc/method/net-physical" failed with exit status 96. [ n

After a memory upgrade all network interfaces are misconfigued. How do i resolve this issue. Below are some out puts.thanks. ifconfig: plumb: SIOCLIFADDIF: eg000g0:2: no such interface # ifconfig eg1000g0:2 plumb ifconfig: plumb: SIOCLIFADDIF: eg1000g0:2: no such interface # ifconfig... (2 Replies)
Discussion started by: andersonedouard
2 Replies

8. UNIX for Dummies Questions & Answers

Confusion Regarding Physical Volume,Volume Group,Logical Volume,Physical partition

Hi, I am new to unix. I am working on Red Hat Linux and side by side on AIX also. After reading the concepts of Storage, I am now really confused regarding the terminologies 1)Physical Volume 2)Volume Group 3)Logical Volume 4)Physical Partition Please help me to understand these concepts. (6 Replies)
Discussion started by: kashifsd17
6 Replies

9. Solaris

Interfaces and Virtual-interfaces queries

Hi Al, In course of understanding networking in Solaris, I have these doubts on Interfaces. Please clarify me. I have done fair research in this site and others but could not be clarified. 1. In the "ifconfig -a" command, I see many interfaces and their configurations. But I see many... (1 Reply)
Discussion started by: satish51392111
1 Replies

10. UNIX for Dummies Questions & Answers

Solaris Logic to transmit traffic to physical interfaces ( eg ce0 and ce1)

Just wanted to understand what is the logic being used by Solaris(kernel) to transmit data/traffic on physical interfaces. I have seen most of the time traffic is being sent to interface ce0 and sometime to ce1. I have removed ip address from below command for some reason. netstat -rn ... (3 Replies)
Discussion started by: nadeemahmed
3 Replies
vni(7d) 							      Devices								   vni(7d)

NAME
vni - STREAMS virtual network interface driver DESCRIPTION
The vni pseudo device is a multi-threaded, loadable, clonable, STREAMS pseudo-device supporting the connectionless Data Link Provider Interface dlpi(7P) Style 2. Note that DLPI is intended to interact with IP, meaning that DLPI access to applications is not supported. (For example, snoop fails on the vni interface.) The vni device is a software-only interface and does not send or receive data. The device provides a DLPI upper interface that identifies itself to IP with a private media type. It can be configured via ifconfig(1M) and can have IP addresses assigned to it, making aliases pos- sible. The vni pseudo device is particularly useful in hosting an IP address when used in conjunction with the 'usesrc' ifconfig option (see ifconfig(1M) for examples). The logical instances of the device can also be used to host addresses as an alternative to hosting them over the loopback interface. Multicast is not supported on this device. More specifically, the following options return an error when used with an address specified on vni: IP_MULTICAST_IF, IP_ADD_MEMBERSHIP, IP_DROP_MEMBERSHIP, IPV6_MULTICAST_IF, IPV6_JOIN_GROUP, IPV6_LEAVE_GROUP. In addition, broadcast is not supported. Because there is no physical hardware configured below it, no traffic can be received through nor transmitted on a virtual interface. All packet transmission and reception is accomplished with existing physical interfaces and tunnels. Because applications that deal with packet transmission and reception (such as packet filters) cannot filter traffic on virtual interfaces, you cannot set up a packet filter on a virtual interface. Instead, you should configure the policy rules to apply to the physical interfaces and tunnels, and if necessary, use the virtual IP addresses themselves as part of the rule configuration. Also, note that the virtual interface cannot be part of an IP multi- pathing (IPMP) group. FILES
/dev/vni 64-bit ELF kernel driver SEE ALSO
ifconfig(1M), in.mpathd(1M), ip(7P), ip6(7P) SunOS 5.10 18 July 2004 vni(7d)
All times are GMT -4. The time now is 01:29 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy