02-12-2009
Jumpstart Issues
Hi all,
I'm having an issue with jumpstart that I haven't seen before. After booting the server and selecting F12 to boot it from the network it finds the jumpstart profile that has been set up for it and proceeds with the build until I get the following error:
SunOS Release 5.10 Version Generic_120012-14 32-bit
Copyright 1983-2007 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
Device is gone
Device is gone
WARNING: BIOS microcode patch for AMD Athlon(tm) 64/Opteron(tm) processor
erratum 131 was not detected; updating your system's BIOS to a version
containing this microcode patch is HIGHLY recommended or erroneous system
operation may occur.
Configuring devices.
Custom JumpStart
Device is gone
Device is gone
Device is gone
Device is gone
Device is gone
Device is gone
Beginning system identification...
Searching for configuration file(s)...
Using sysid configuration file *.*.*.*:/data/jumpstart/sysidcfg/solaris_10/sysid g
Search complete.
Discovering additional network configuration...
Completing system identification...
Starting remote procedure call (RPC) services: done.
It crashes out at this point. I've built other boxes using this method with no issues, any idea of what could be causing this?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have been asked to research Jumpstart and don't know where to begin! Any ideas would be much appreciated! Thanks! :-) (1 Reply)
Discussion started by: avana100
1 Replies
2. UNIX for Dummies Questions & Answers
Hi,
Which sites have general information on JumpStart for Solaris 8?
I would like to know more about boot server, installation server, and configuration server.... and all other good things about JumpStart....Thanks..:p
Doo... (2 Replies)
Discussion started by: dookeobih
2 Replies
3. UNIX for Advanced & Expert Users
HI.
i was wondering if you can jumpstart using the solaris intel platform? please help thanks (3 Replies)
Discussion started by: souldier
3 Replies
4. UNIX for Advanced & Expert Users
Hi,
where can i find documention on how to create a jumpstart system?
dori (2 Replies)
Discussion started by: dorilevy
2 Replies
5. Solaris
Hello all,
I configured a jumpstart server ( the server is in the same subnet as the client) and gave boot net - install in the client.
The client boots up shows the banner and then displays error:
cant read disk label
cant open disk label package
and then goes to OK prompt.
What... (1 Reply)
Discussion started by: Pratik Gharti
1 Replies
6. Solaris
Hi Peeps,
Created a jumpstart server for an unattened install and it works, but got 2 bugs in the config which I would like to work out:
when you boot net install
It still asks you to select a language and locale, after you do this it kicks of an unattended install.
So my question is,... (5 Replies)
Discussion started by: callmebob
5 Replies
7. Solaris
I'm trying to jumpstart my remote server. My /etc/hosts and /etc/ethers files have the correct data. Keep getting the following message at the ok prompt
after running a boot net - install
Link hasn't comeup yet
Ran a test-net and got the following message.
Link is -- down
When... (7 Replies)
Discussion started by: soupbone38
7 Replies
8. Solaris
hi friends,
i dont know how to install jumpstart . i have solaris cds( 5 nos.). i tried to install jumpstart but there is no setup_install_server file. What i want to do for installing jumpstart server
please help me
thanks to all (8 Replies)
Discussion started by: sijocg
8 Replies
9. Solaris
1.I wish to perform a Jumpstart installation, the client being Ultra 5 Sparc
and jumpstart Server being ultra 20 AMD system.
2.I think i have done all the procedures right, like putting the mac address of Sparc 1 to /etc/ethers, creating sysidcfg file, and profile file:
3.When I issued the boot... (7 Replies)
Discussion started by: saagar
7 Replies
10. Solaris
I'm trying to use a V210 (sun4u) configured as a jumpstart server to flash install a number of T5220's (sunv4).
The Facts:
V210 - Solaris 10 (September 2010 Release / not patched)
T5220's - Archive's created using prior (unknown) version of solaris 10.
Flar -i <archive name> shows the... (6 Replies)
Discussion started by: Celtic_Monkey
6 Replies
LEARN ABOUT LINUX
devinfo
devinfo(1M) System Administration Commands devinfo(1M)
NAME
devinfo - print device specific information
SYNOPSIS
/usr/sbin/devinfo -i device
/usr/sbin/devinfo -p device
DESCRIPTION
The devinfo command is used to print device specific information about disk devices on standard out. The command can only be used by the
superuser.
OPTIONS
-i Prints the following device information:
o Device name
o Software version (not supported and prints as 0)
o Drive id number (not supported and prints as 0)
o Device blocks per cylinder
o Device bytes per block
o Number of device partitions with a block size greater than zero
-p Prints the following device partition information:
o Device name
o Device major and minor numbers (in hexadecimal)
o Partition start block
o Number of blocks allocated to the partition
o Partition flag
o Partition tag
This command is used by various other commands to obtain device specific information for the making of file systems and determining parti-
tion information. If the device cannot be opened, an error message is reported.
OPERANDS
device Device name.
EXIT STATUS
0 Successful operation.
2 Operation failed.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
prtvtoc(1M), attributes(5)
SunOS 5.10 8 May 1997 devinfo(1M)