02-10-2009
whether the interface is recognized during installation or not doesn't mean the interface doesn't work. could be that this interface is not native to sol10 os. as long as the correct drivers are loaded into the kernel, the interface will work as advertised. i'm going with incredible on this one.
what is the output of the following commands:
dladm show-dev
netstat -rn
cat /etc/netmask
cat /etc/defaultrouter
10 More Discussions You Might Find Interesting
1. IP Networking
i just linked 2 100MHz Linux kernel 2.4.2 boxes togeather using a direct cable connection, on two 3Com PCI network cards, using the EtherLink III chipset. Unfortuanately, when I boot both PCs, i get a loading interface: eth0 for five minutes, then a failed flag. No networking suppt. in windows,... (2 Replies)
Discussion started by: boris888
2 Replies
2. Solaris
I have a solaris x86 box that ive been having trouble getting on my network, anyone know a good guide that can take me through it step by step? (1 Reply)
Discussion started by: xtremepancakez
1 Replies
3. Solaris
i am not able to install solaris 10
i have installed solaris many times succesfully with wotking network
after that abrupt power failure i was never able to start solaris and neither install during install it hangs
IS IT PROBABLE THAT BIOS OR SOME OTHER SETTINGS RELATED TO HARDWARE IS... (3 Replies)
Discussion started by: simaich8
3 Replies
4. Solaris
hi all,
how do i change the routing info and make sure i will be able to connect remotely?
any ideas please?
thanks in advance. (5 Replies)
Discussion started by: itik
5 Replies
5. Solaris
Hi
I compiled an executable on Solaris 10 which creates semaphore ( semget)
but it didn't work on solaris 9 , while it is executing sucessfully on solaris 10. It is throwing the system error that Invalid arguments ( system error 22) on solaris 9.
the ldd for the executable on two servers is as... (4 Replies)
Discussion started by: ash_bit2k2
4 Replies
6. Ubuntu
Hi,
I am a new to Ubuntu linux and trying to learn it. I am using ubuntu 10.04. I am getting problem in setting my wireless network. I set it up properly and was working fine. But suddenly it stopped working, though the wireless icon saying that it is connected, but can't load any page. I... (2 Replies)
Discussion started by: linux_learner
2 Replies
7. SCO
I am trying to get a network printer to work that currently works from my Unix (5.0.7) server when printing text files only. When I try to print post script files like a PDF file I get all of the controls so I am not sure if I have my printer configuration setup properly in Unix
The printer... (1 Reply)
Discussion started by: ziggy6
1 Replies
8. Solaris
Hello,
I have a problem.
I have a server SPARC T3-1 with solaris 11 on the base. The server is working well. And then i did a virtual machine using again Solaris 11 to do this, but now my notwork on my virtual machine is not working anymore. There says that the network that i have created is... (11 Replies)
Discussion started by: keziacp
11 Replies
9. Red Hat
I was testing Networking Teaming (activebackup) with a VM hosted on VmWare Workstation and VirtualBox, and the result is, if the active interface is down, the system is not using the backup interface.
Tested on both CentOS / RHEL 7
Please find below the command I have used to configure teaming.... (0 Replies)
Discussion started by: atanubanerji
0 Replies
10. UNIX for Beginners Questions & Answers
I'm really stuck here. I've created an LDOM on a SPARC T4-1 with Solaris 11.4 to run a copy of Linux for SPARC. I got the Linux ISO installed and Linux itself installed and booted OK. The only thing is is that there's no networking available in the Linux guest.
This question is basically the... (7 Replies)
Discussion started by: Michele31416
7 Replies