02-08-2009
Quote:
Originally Posted by
vettec3
If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping.
What is the IP address of your laptop when you are pinging the default gateway from that laptop?
Please post the arp tables of both the laptop and the server?
10 More Discussions You Might Find Interesting
1. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
2. Solaris
I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
Discussion started by: cesmk
2 Replies
3. AIX
Hello,
I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies
4. Red Hat
I know the subject line is very similar to: destination host unreachable
but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there.
We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Discussion started by: mirage
1 Replies
5. AIX
Just want to know if someone has a clue about what could be happening here:
I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.
When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.
Thanks... (1 Reply)
Discussion started by: witt
1 Replies
6. UNIX for Dummies Questions & Answers
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies
7. AIX
I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a
startsrc -g tcpip
... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies
8. Red Hat
Hi,
Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Discussion started by: aixlover
4 Replies
9. AIX
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies
10. UNIX for Advanced & Expert Users
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies
dceping(8) dceping(8)
NAME
dceping - test the ability to contact DCE services from a local DCE client.
SYNOPSIS
dceping [-n number] [-s time] [-v] [-C] [service_name ...] required to specify the literal strings, NAMESPACE or STRING_BINDING (see nond-
cesvc(4)).
OPTIONS
-n number Specify the number of pinging cycles. Each service is tested once per cycle. The default is one pinging cycle. Specifying -n 0
makes pinging continuous.
-s time Specify time, in seconds, to wait between pinging cycles. You must specify more than one pinging cycle with the -n option in
order to use -s.
-v Run in verbose mode.
-C Ping only core DCE services. This option is ineffective if a service_name is specified on the command line.
DESCRIPTION
dceping verifies that a local DCE client can communicate with DCE and other services. It uses the RPC management interface to determine if
the DCE service is listening. The core DCE services that dceping checks include secd, cdsd, gdad, rpcd, cdsadv, dtsd, and sec_clientd.
You can ping other DCE and non-DCE services by naming them in the file, /opt/dcelocal/hpadmin/etc/nondcesvc. If you want to determine at
run time what services you want dceping to ping, you may do so using the same file. See the manpage, nondcesvc(4), for more information.
You may specify the services to ping on the command line separated by blanks. In this case, dceping does not ping any DCE core services or
the services listed in /opt/dcelocal/hpadmin/etc/nondcesvc. The service_name specified could be either a name in the DCE Cell Directory
Service Namespace or an RPC string binding. It is not
AUTHOR
dceping was developed by HP.
FILES
/opt/dcelocal/hpadmin/etc/nondcesvc
/opt/dcelocal/hpadmin/etc/wellknownif
SEE ALSO
nondcesvc(4), wellknownif(4)
HP DCE
dceping(8)