Sponsored Content
Full Discussion: Help with Default Gateway
Operating Systems AIX Help with Default Gateway Post 302284978 by Padow on Friday 6th of February 2009 04:45:21 PM
Old 02-06-2009
when configuring the second interface (that should not have a default gateway) use
Code:
smitty chinet

Another note: if you have two default gateways, they will both come back on a reboot even if you do a route delete. You must use
Code:
smitty route

to delete the second route to clean it out of the system completly.

Are you sure you configured the two adapters for the right networks (you don't have them backwards)? Is your netmask set properly on both adapters?

Edit: I edited the first command from smitty mktcpip to smitty chinet. Had a brain fart.

Last edited by Padow; 02-06-2009 at 05:51 PM..
Padow
 

9 More Discussions You Might Find Interesting

1. HP-UX

How to add another default gateway

I am using HP-UX 11i and I need to add another default gateway. how can I do that ? (3 Replies)
Discussion started by: salhoub
3 Replies

2. Solaris

How can I change the default gateway?

my actual default gatewas IP is: default 192.168.11.254 and I need to change it to 192.168.11.2, I'm using Solaris 9, how can i do it? and how i can save it in case that the machine restart and have the new default gateway IP saved? (5 Replies)
Discussion started by: Lestat
5 Replies

3. IP Networking

default gateway in unix?

i'm a real unix newbie, setting up a network, with a router to router vpn connection with a remote site, all the win stuff is talking and pinging and all the stuff it should be doing (yeah and crashing too, lol) but no communication with the unix box, i think the problem is with my default... (3 Replies)
Discussion started by: smcg
3 Replies

4. HP-UX

where can i modify default gateway

where in configuration files can i modify default gateway in hp-ux11iv3 (5 Replies)
Discussion started by: h@foorsa.biz
5 Replies

5. Linux

GNUGK-How to setup static gateway to gateway routing

Dear Sir I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper. I am having a problem, configuring static call routing on GNUGK in the section ... (0 Replies)
Discussion started by: mfondoum
0 Replies

6. Red Hat

Can not ping default gateway

Hi, Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Discussion started by: aixlover
4 Replies

7. Red Hat

Change Default gateway

Hi..I have to change default gateway in my linux machine. Its OS is RHEL6. I followed following steps. 1.run command ip route to check current default gateway 2.delete that gateway with command route del default gw x.x.x.x eth2 3.Add new gatewy with command below route add default gateway... (3 Replies)
Discussion started by: deljatt
3 Replies

8. IP Networking

Default Gateway

I am am using IPv6 IP's with an OS of Debian. Is it possible to set a *static* default gateway w/o the router being connected? Will that gateway change when the router is connected? TIA (0 Replies)
Discussion started by: Meow613
0 Replies

9. UNIX for Beginners Questions & Answers

Inconsistency between RedHat 6.5 global gateway and single gateway leads to loss of default gateway

Dear friends I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
DUMP_SOCKDFR(8) 					      System Manager's Manual						   DUMP_SOCKDFR(8)

NAME
dump_sockdfr - Display contents of frozen route file for SOCKS server SYNOPSIS
dump_sockdfr [infile] DESCRIPTION
dump_sockdfr reads in a frozen route file for the SOCKS server and produces a listing of its contents on the standard output. The argument is optional; if omitted, /etc/sockd.fr is assumed. The frozen route file is produced by make_sockdfr and is essentially the memory image of the parsed route file. Using the frozen route file can reduce the start-up delay of the SOCKS server program since it no longer has to parse the file contents. When the SOCKS server starts, it always looks for the frozen route file /etc/sockd.fr first. If that file is not found, it then tries to use the plain-text route file /etc/sockd.route. If you use frozen route file, you must remember to run make_sockdfr every time after you modify the plain-text file or the SOCKS server will continue to use the frozen version of a previous route file. FILES
/etc/sockd.fr, /etc/sockd.route SEE ALSO
make_sockdfr(8), sockd.fr(5), sockd.route(5) AUTHOR
Ying-Da Lee, yingda@esd.sgi.com or yingda@best.com May 6, 1996 DUMP_SOCKDFR(8)
All times are GMT -4. The time now is 01:37 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy