02-05-2009
Where could I save the routes created using route add ?
Hey Gurus.
My routes add using route add , are lost , after reboot.....where caould i save this routes a dont lost them ? Sun Solaris 10 is my OS.
Thanks in advance,
AGADEA. Unix ADMIN
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I need some help adding routes in sco.
I am using SCO Openserver 5.0.4.
Basically I have 2 gateways here. The first is 10.15.1.1 and allows me access to the rest of the computers in the office and in other offices.
The other gateway is 10.15.10.2 and is the sonicwall that will allow access... (3 Replies)
Discussion started by: cstovall
3 Replies
2. AIX
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies
3. IP Networking
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies
4. SCO
Hi,
I add following routes manually each time system reboots:
#route add 192.168.1.0 -gateway 192.168.0.90
#route add 192.168.200.0 -gateway 192.168.0.200
Is there any way in SCO 7.1.1 to automate this route add process? i.e. each time system reboots, it automatically adds these routes in... (1 Reply)
Discussion started by: tayyabq8
1 Replies
5. AIX
Hi,
IBM Server with AIX 5.2. I have already added a static route for a whole network but everyday some automatic routes to hosts adds up in route table of this server, some of which invalid routes that stops communication of server to that network. If these invalid routes are removed from route... (0 Replies)
Discussion started by: system-admin
0 Replies
6. IP Networking
I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system.
The ip i am trying to get to is 172.16.4.48
I need to get to it via the hme1 interface.
The vpn gateway has this ip 172.30.50.1
I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies
7. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
8. Solaris
Hi,
I need help to add new route:
10.252.0.138, GW 10.252.0.129 to e1000g1
and
10.252.0.10, GW 10.252.0.1 to e1000g2
tnx (4 Replies)
Discussion started by: mehrdad68
4 Replies
9. SCO
Hi all,
n00b here. We currently have 3 SCO 5.0.5 machines in our network that run a mission management system.
Our internal network was always a 10.0.0.0 network and the machines worked fine.
Our company is going through a network upgrade for VoIP and some of our departments are now on... (5 Replies)
Discussion started by: gibson_hg
5 Replies
10. IP Networking
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies
LEARN ABOUT CENTOS
nrparms
NRPARMS(8) Linux System Managers Manual NRPARMS(8)
NAME
nrparms - Configure the NET/ROM interface.
SYNOPSIS
nrparms -nodes node +|- ident quality count port neighbour [digicall...]
nrparms -routes port nodecall [digicall...] +|- quality
nrparms -version
DESCRIPTION
This program is used to manipulate the routing tables of the NET/ROM network layer, or to get and set many of the network and transport
layer parameters for the NET/ROM protocol. The program has three basic modes of operation, node setting, neighbour setting and general
parameter setting. The syntax for the node and neighbour setting is taken from the original NET/ROM manual and is therefore not very UNIXy
but should be familiar to those familiar with NET/ROMs or TheNet.
To set up a new route to a NET/ROM node in the routing tables you must use the nodes option. All of the parameters are needed to add the
node. It is probably best to illustrate with an example:
nrparms -nodes GB7BPQ + NMCLUS 120 6 vhf G8ROU-3
This creates a new route to a distant node with the callsign GB7BPQ and the alias NMCLUS, it has a quality of 120 (out of 255) and has an
obsolescence count of six and packets for that node should be sent on the AX.25 port named vhf to my immediate neighbour G8ROU-3. The call-
signs of the node and the neighbour may be the same. For example to set up the node G8ROU-3 which is also my immediate neighbour, I would
use:
nrparms -nodes G8ROU-3 + MATLCK 200 6 vhf G8ROU-3
If the ident of the remote node is not known, it is possible to add a node with a blank ident. To do this an ident of '*' must be entered
on the command line. Because of the command line expansion that shells do, the * must be escaped by enclosing it in quotes.
It is also possible to remove a route to a distant node with the same command except that the + is replaced by a -. The other parameters
must also be present. If the node has not other routes then the node will be deleted, and the neighbour node that the connections go via
may also be deleted if no other node route uses it, and it is not a locked neighbour entry.
When setting up a new node, a new neighbour entry may also be created. This will have a default value. For that neighbour to be meaningful
in the automatic routing process, it must have a more reasonable entry in the neighbours list. To do this the routes option of the command
must be used. An example:
nrparms -routes ax0 G8ROU-3 + 120
This will create (or update) the neighbour entry for G8ROU-3 with a quality of 120 and it will be locked, it will not create a node entry
for the neighbour. This quality will be used by the netromd(8) program when calculating route qualities via this neighbour. Normally once a
neighbour has zero node routes going via it, it will be deleted. Locking a neighbour prevents the deletion from occurring. To unlock a
neighbour entry, the same command is used but with the + replaced by a -.
FILES
/etc/ax25/axports
/etc/ax25/nrports
SEE ALSO
call(1), netrom(4), nrports(5), axparms(8), netromd(8), nrparms(8).
AUTHOR
Jonathan Naylor G4KLX <g4klx@g4klx.demon.co.uk>
Linux 25 January 1997 NRPARMS(8)