02-03-2009
hi
for y info
Minimum Supported Solaris[tm] Operating Environment Versions T5240
Solaris 10 8/07 (U4) plus patches *
10 More Discussions You Might Find Interesting
1. Solaris
I know that I could use the
#ifconfig hme0 plumb
to activate the network interface.
However, how can I know the name of the interface e.g. hme0 before I could use the ifconfig to plumb it up?
I know there is a command (but I forgot it) to use in the Sparc version when you are in the... (7 Replies)
Discussion started by: heero
7 Replies
2. Solaris
Setting up a T5240 with two disks c1t0d0 and c1t1d0.
I am trying to use raidctl but when I issue.
raidctl -l
I get
Controller 1
Disk: 0.0.0
Disk: 0.1.0
So I try
raidctl -c '0.0.0 0.1.0' -r 1 1
and I get "Array in use."
I try (4 Replies)
Discussion started by: photon
4 Replies
3. Solaris
Hi,
We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions.
RJS (4 Replies)
Discussion started by: rajasekg
4 Replies
4. Solaris
Hi Friends
we have sun T5240 server, we have taken ufsdump of this server remotely with scsi tapedrive, If we need to do ufsrestore means what we have to do, since T5240 has not having scsi port, any procedure is there?
Regards
Rajasekar (5 Replies)
Discussion started by: rajasekg
5 Replies
5. Solaris
Hi all, I would like to tune the nxge card as suggested by this link, but got some confusion. Can anyone advise me ?
We have
SunOS hsbc02 5.10 Generic_137137-09 sun4v sparc SUNW,Netra-CP3260
Do I have to install any patches ?
The tunning link
Networks - Siwiki
In our nxge.conf, I... (0 Replies)
Discussion started by: dehetoxic
0 Replies
6. Solaris
Hi all,
I am writing this post in order to share my experience with the SUN nxge ethernet interfaces and try to see if some of you managed to solve similar issues than the ones we experienced here with T5520 running Solaris 10.
First, we noticed that it was somehow difficult to have those... (5 Replies)
Discussion started by: fpraile
5 Replies
7. Solaris
Hiii folks,,
I am unable to configure NIC using hme0 command. I am getting an error message as "hme0: File or directory not found.."
can someone help me...
Bhagi... (9 Replies)
Discussion started by: bhargav90
9 Replies
8. Solaris
Hello Folks, can anyone please help me with this ?! :wall:
I'm using Solaris 10 with Sun V880 which has two Networks Interfaces, a Fiber (ge0) and a cooper (eri0).
The eri0 is working great but when I try to plumb the ge0 interface ...
# ifconfig ge0 plumb
ifconfig: cannot open link... (18 Replies)
Discussion started by: pxb368@motorola
18 Replies
9. Solaris
Hi !
I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before.
I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl.
... (2 Replies)
Discussion started by: delavega
2 Replies
10. Solaris
Hi Folks,
Just a quick question - hopefully!
I have an application currently running on a V890 with Solaris 9, I'd like to move this to either one of our T-5's or one of the T5240's in a Legacy container on an LDOM - but the fly in the ointment is the application still uses a standard Hayes... (3 Replies)
Discussion started by: gull04
3 Replies
LEARN ABOUT OPENSOLARIS
install-solaris
install-solaris(1M) install-solaris(1M)
NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)