cannot plumb nxge on T5240 Post: 302283243

Sponsored Content

Operating Systems Solaris cannot plumb nxge on T5240 Post 302283243 by incredible on Tuesday 3rd of February 2009 12:43:02 AM

02-03-2009

Registered User

cannot plumb nxge on T5240

its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file.
getting similar error on bootup/messages file
WARNING: consconfig: cannot find driver for screen device
WARNING: ncp0: unable to determine ncp (cpu) binding (ncp)
Booting to milestone "milestone/single-user:default".
WARNING: ncp0: unable to determine ncp (cpu) binding (ncp)
Failed to plumb IPv4 interface(s): nxge0
Feb 2 17:58:56 svc.startd[7]: svc:/network/physical:default: Method "/lib/svc/m
ethod/net-physical" failed with exit status 96.
Feb 2 17:58:56 svc.startd[7]: network/physical:default misconfigured: transitio
ned to maintenance (see 'svcs -xv' for details)
Hostname: xxxxxxx

incredible

View Public Profile for incredible

Find all posts by incredible

10 More Discussions You Might Find Interesting

1. Solaris

Before plumb the network interface.....

I know that I could use the #ifconfig hme0 plumb to activate the network interface. However, how can I know the name of the interface e.g. hme0 before I could use the ifconfig to plumb it up? I know there is a command (but I forgot it) to use in the Sparc version when you are in the...

2. Solaris

raidctl on SUN T5240

Setting up a T5240 with two disks c1t0d0 and c1t1d0. I am trying to use raidctl but when I issue. raidctl -l I get Controller 1 Disk: 0.0.0 Disk: 0.1.0 So I try raidctl -c '0.0.0 0.1.0' -r 1 1 and I get "Array in use." I try

3. Solaris

SUN T5240 vs M3000

Hi, We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions. RJS

4. Solaris

ufsrestore T5240

Hi Friends we have sun T5240 server, we have taken ufsdump of this server remotely with scsi tapedrive, If we need to do ufsrestore means what we have to do, since T5240 has not having scsi port, any procedure is there? Regards Rajasekar

5. Solaris

nxge tuning

Hi all, I would like to tune the nxge card as suggested by this link, but got some confusion. Can anyone advise me ? We have SunOS hsbc02 5.10 Generic_137137-09 sun4v sparc SUNW,Netra-CP3260 Do I have to install any patches ? The tunning link Networks - Siwiki In our nxge.conf, I...

6. Solaris

nxge interfaces too sensitive ?

Hi all, I am writing this post in order to share my experience with the SUN nxge ethernet interfaces and try to see if some of you managed to solve similar issues than the ones we experienced here with T5520 running Solaris 10. First, we noticed that it was somehow difficult to have those...

7. Solaris

ifconfig hme0 plumb not working

Hiii folks,, I am unable to configure NIC using hme0 command. I am getting an error message as "hme0: File or directory not found.." can someone help me... Bhagi...

8. Solaris

ifconfig ge0 plumb

Hello Folks, can anyone please help me with this ?! :wall: I'm using Solaris 10 with Sun V880 which has two Networks Interfaces, a Fiber (ge0) and a cooper (eri0). The eri0 is working great but when I try to plumb the ge0 interface ... # ifconfig ge0 plumb ifconfig: cannot open link...

9. Solaris

Cannot configure RAID on T5240

Hi ! I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before. I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl. ...

10. Solaris

Using a Modem on a T5-2 or a T5240

Hi Folks, Just a quick question - hopefully! I have an application currently running on a V890 with Solaris 9, I'd like to move this to either one of our T-5's or one of the T5240's in a Legacy container on an LDOM - but the fly in the ointment is the application still uses a standard Hayes...

LEARN ABOUT OPENDARWIN

svc.configd

svc.configd(1M)                                                                                                                    svc.configd(1M)

NAME

       svc.configd - Service Management Facility repository daemon

SYNOPSIS

       /lib/svc/bin/svc.configd

       svc.configd  is  the repository daemon for the Service Management Facility. svc.configd is invoked automatically during system startup, and
       restarted if any failures occur. svc.configd should never be invoked directly.

       Interaction with svc.configd is by way of libscf(3LIB) and the command line tools:svcs(1), svcprop(1), svcadm(1M), and svccfg(1M).

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE         |      ATTRIBUTE VALUE        |
       +-----------------------------+-----------------------------+
       |Availability                 |SUNWcsr                      |
       +-----------------------------+-----------------------------+

       svcs(1), svcprop(1), svcadm(1M), svccfg(1M), libscf(3LIB), attributes(5)

                                                                    27 Oct 2004                                                    svc.configd(1M)