Sponsored Content
Full Discussion: cannot plumb nxge on T5240
Operating Systems Solaris cannot plumb nxge on T5240 Post 302283243 by incredible on Tuesday 3rd of February 2009 12:43:02 AM
Old 02-03-2009
Data cannot plumb nxge on T5240

its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file.
getting similar error on bootup/messages file
WARNING: consconfig: cannot find driver for screen device
WARNING: ncp0: unable to determine ncp (cpu) binding (ncp)
Booting to milestone "milestone/single-user:default".
WARNING: ncp0: unable to determine ncp (cpu) binding (ncp)
Failed to plumb IPv4 interface(s): nxge0
Feb 2 17:58:56 svc.startd[7]: svc:/network/physical:default: Method "/lib/svc/m
ethod/net-physical" failed with exit status 96.
Feb 2 17:58:56 svc.startd[7]: network/physical:default misconfigured: transitio
ned to maintenance (see 'svcs -xv' for details)
Hostname: xxxxxxx
 

10 More Discussions You Might Find Interesting

1. Solaris

Before plumb the network interface.....

I know that I could use the #ifconfig hme0 plumb to activate the network interface. However, how can I know the name of the interface e.g. hme0 before I could use the ifconfig to plumb it up? I know there is a command (but I forgot it) to use in the Sparc version when you are in the... (7 Replies)
Discussion started by: heero
7 Replies

2. Solaris

raidctl on SUN T5240

Setting up a T5240 with two disks c1t0d0 and c1t1d0. I am trying to use raidctl but when I issue. raidctl -l I get Controller 1 Disk: 0.0.0 Disk: 0.1.0 So I try raidctl -c '0.0.0 0.1.0' -r 1 1 and I get "Array in use." I try (4 Replies)
Discussion started by: photon
4 Replies

3. Solaris

SUN T5240 vs M3000

Hi, We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions. RJS (4 Replies)
Discussion started by: rajasekg
4 Replies

4. Solaris

ufsrestore T5240

Hi Friends we have sun T5240 server, we have taken ufsdump of this server remotely with scsi tapedrive, If we need to do ufsrestore means what we have to do, since T5240 has not having scsi port, any procedure is there? Regards Rajasekar (5 Replies)
Discussion started by: rajasekg
5 Replies

5. Solaris

nxge tuning

Hi all, I would like to tune the nxge card as suggested by this link, but got some confusion. Can anyone advise me ? We have SunOS hsbc02 5.10 Generic_137137-09 sun4v sparc SUNW,Netra-CP3260 Do I have to install any patches ? The tunning link Networks - Siwiki In our nxge.conf, I... (0 Replies)
Discussion started by: dehetoxic
0 Replies

6. Solaris

nxge interfaces too sensitive ?

Hi all, I am writing this post in order to share my experience with the SUN nxge ethernet interfaces and try to see if some of you managed to solve similar issues than the ones we experienced here with T5520 running Solaris 10. First, we noticed that it was somehow difficult to have those... (5 Replies)
Discussion started by: fpraile
5 Replies

7. Solaris

ifconfig hme0 plumb not working

Hiii folks,, I am unable to configure NIC using hme0 command. I am getting an error message as "hme0: File or directory not found.." can someone help me... Bhagi... (9 Replies)
Discussion started by: bhargav90
9 Replies

8. Solaris

ifconfig ge0 plumb

Hello Folks, can anyone please help me with this ?! :wall: I'm using Solaris 10 with Sun V880 which has two Networks Interfaces, a Fiber (ge0) and a cooper (eri0). The eri0 is working great but when I try to plumb the ge0 interface ... # ifconfig ge0 plumb ifconfig: cannot open link... (18 Replies)
Discussion started by: pxb368@motorola
18 Replies

9. Solaris

Cannot configure RAID on T5240

Hi ! I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before. I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl. ... (2 Replies)
Discussion started by: delavega
2 Replies

10. Solaris

Using a Modem on a T5-2 or a T5240

Hi Folks, Just a quick question - hopefully! I have an application currently running on a V890 with Solaris 9, I'd like to move this to either one of our T-5's or one of the T5240's in a Legacy container on an LDOM - but the fly in the ointment is the application still uses a standard Hayes... (3 Replies)
Discussion started by: gull04
3 Replies
ncp(7D) 																   ncp(7D)

NAME
ncp - Niagara crypto provider device driver The ncp device driver is a multi-threaded, loadable hardware driver supporting hardware assisted acceleration of RSA and DSA cryptographic operations. This support is built into the Niagara CMT processor. The ncp driver requires the presence of the Solaris Cryptographic Framework to enable applications and kernel clients to access the pro- vided services. CONFIGURATION
You configure the ncp driver by defining properties in /platform/sun4v/kernel/drv/ncp.conf which override the default settings. The fol- lowing property is supported: nostats Disables the generation of statistics. The nostats property may be used to help prevent traffic analysis, but this may inhibit support personnel. NETWORK STATISTICS
Solaris network drivers must implement statistics variables. The ncp driver maintains the following statistics: mauXqfull Number of times the queue for MAU X was found full when attempting to submit jobs. mauXupdate_failure Number of submit job failures on MAU X. mauXsubmit Number of jobs submitted to MAU X since driver load (boot). rsapublic Total number of jobs submitted to the device for RSA public key operations. rsaprivate Total number of jobs submitted to the device for RSA private key operations. dsasign Total number of jobs submitted to the device for DSA signing. dsaverify Total number of jobs submitted to the device for DSA verification. Additional statistics may be supplied for Sun support personnel, but are not useful to Solaris users and are not doc- umented in this manpage. See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Architecture |SPARC | +-----------------------------+-----------------------------+ |Availability |SUNWcakr.v | +-----------------------------+-----------------------------+ |Interface Stability |Unstable | +-----------------------------+-----------------------------+ FILES
/platform/sun4v/kernel/drv/sparcv9/ncp 64-bit ELF kernel driver. /platform/sun4v/kernel/drv/ncp.conf Configuration file. cryptoadm(1M), kstat(1M), prtconf(1M), attributes(5) Solaris Cryptographic Framework -- Solaris Software Developer Collection Solaris Security for Developer's Guide -- Solaris Software Developer Collection 14 Mar 2005 ncp(7D)
All times are GMT -4. The time now is 03:45 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy