Sponsored Content
Operating Systems AIX AIX Boots straight to service mode Post 302283121 by gsorin on Monday 2nd of February 2009 03:46:14 PM
Old 02-02-2009
Hi,
I tried to enable multiboot and it always enters the boot menu in SMS. If I disable multiboot it goes to service (diagnostics) mode.

The output from bootlist -om normal is
hdisk1 blv=hd5

If I do a df I get:
/dev/hd1 -> /home
/dev/hd2 -> /usr
/dev/hd3 -> /tmp
/dev/hd4 -> /
/dev/hd9var -> /var
/dev/hd10opt -> /opt

In SMS boot options if I list all available boot devices I get:

1. Ethernet
2. Ethernet
3. IDE CDROM
4. SCSI 166814 MB Harddisk
5. SCSI 166814 MB Harddisk, part=2 (AIX 5.2.0)
6. SCSI 166814 MB Harddisk
7. SCSI Tape

It's strange about the bootlist because if I go into SMS and set the boot order and boot device it creates a good bootlist (I can check it after the operating system has started) however, after the reboot it doesn't keep the normal mode, it goes to service mode (diagnostics mode).

Thanks.
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

AIX 433 boots into command line.

Hi All, I have an AIX 433 workstation that keeps booting into command mode. It was booting into CDE for a long time now. Suddenly now it boots into command line mode. No errors while booting up. Do not see anything in errpt. Don' t know where to start from.. Can any one please help me..thanks. ... (2 Replies)
Discussion started by: navinxavier
2 Replies

2. AIX

Enter in Service Mode

Hello I am newbie user and have got a Server (RS / 6000 H70). The vendor don't gave me the root password and the ip number, I can't enter en service mode. I pressed the button 5,1,6 in the terminal ASCII, but it does't responded. I use minicom with the specification on the manual documentation... (0 Replies)
Discussion started by: Rinux
0 Replies

3. Solaris

Service Mode on XSCF

While entering to service mode on XSCF i getting following error XSCF> service Account is not enabled for service mode. What could be the reason for this ? (5 Replies)
Discussion started by: fugitive
5 Replies

4. AIX

Transferring files from one AIX server to another AIX server in binary mode

Hi, I am a newbie to AIX. We have 2 AIX5.3 servers in our environment, I need to transfer some files in Binary mode from one server to another and some files in ASCII mode from one server to another server. Could you please help me as to how I need to do that? Thanks, Rakesh (4 Replies)
Discussion started by: rakeshc.apps
4 Replies

5. Solaris

Samba service in maintenance mode ???

I have a Solaris 10 SunFire v880 machine and I'm having trouble with Samba. Samba has worked on this machine but since the machine has been re-booted Samba has not worked. Machine details are: cat /etc/release Solaris 10 10/08 s10s_u6wos_07b SPARC Copyright 2008... (2 Replies)
Discussion started by: KenLynch
2 Replies

6. Solaris

Helpme !! ssh service in maintenance mode

Hi Guys, Virtual Machine - Solaris 10 ssh service is in maintenance mode, when i tried to disable it it got disabled but when i enabling it ( svcadm enable ssh) it is coming in maintenance mode...... Pls help (10 Replies)
Discussion started by: saurabh84g
10 Replies

7. Solaris

Solaris 10 system boots into Maintenance mode

I have seen similar threads on this issue, but I have not seen a fix. Basically I am getting a lot of rcp bind errors. Below find the output of "svcs -xv". not sure where to begin: # svcs -xv svc:/network/rpc/bind:default (RPC bindings) State: maintenance since Fri May 25 14:13:18 2012... (14 Replies)
Discussion started by: brownwrap
14 Replies

8. Solaris

DNS service is in maintenance mode. How to bring it back to online mode?

:confused: when i tried to look the status of DNS-client, it is in maintenance mode..... Please tell me how to bring it back to online mode...PLEASE TELL ME STEP BY STEP.... PLEASE... :wall: (2 Replies)
Discussion started by: vamshigvk475
2 Replies

9. Solaris

RPC bind service in maintenance mode

Hi, I have an issue with RPC bind service and its failing with status 1. any help would be much appreciated. THanks (2 Replies)
Discussion started by: Yakub Humami
2 Replies

10. Solaris

SunOS sun4v sparc ntp service in maintenance mode.

Hi experts, This is a production server. Host information's are below SunOS hostname_srv 5.10 Generic_150400-09 sun4v sparc sun4v Now issue with ntp service, This host have zone in it with 9 hosts, Every hosts have ntp service issue. While i check for the service status it's in... (3 Replies)
Discussion started by: babinlonston
3 Replies
installboot(1M) 														   installboot(1M)

NAME
installboot - install bootblocks in a disk partition SYNOPSIS
installboot bootblk raw-disk-device The boot(1M) program, ufsboot, is loaded from disk by the bootblock program which resides in the boot area of a disk partition. The ufs boot objects are platform-dependent, and reside in the /usr/platform/platform-name/lib/fs/ufs directory. The platform name can be found using the -i option of uname(1). The installboot utility is a SPARC only program. It is not supported on the architecture. users should use installgrub(1M) instead. bootblk The name of the bootblock code. raw-disk-device The name of the disk device onto which the bootblock code is to be installed; it must be a character device which is read- able and writable. Naming conventions for a SCSI or IPI drive are c?t?d?s? and c?d?s? for an IDE drive. Example 1: Installing UFS Boot Block To install a ufs boot block on slice 0 of target 0 on controller 1 of the platform where the command is being run, use: example# installboot /usr/platform/`uname -i`/lib/fs/ufs/bootblk /dev/rdsk/c1t0d0s0 /usr/platform/platform-name/lib/fs/ufs directory where ufs boot objects reside. /platform/platform-name/ufsboot second level program to boot from a disk or CD See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ od(1), uname(1), boot(1M), init(1M), kadb(1M), kernel(1M), monitor(1M), reboot(1M), rpc.bootparamd(1M), init.d(4), attributes(5) WARNINGS
The installboot utility fails if the bootblk or openfirmware files do not exist or if the raw disk device is not a character device. 11 Apr 2005 installboot(1M)
All times are GMT -4. The time now is 06:43 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy