01-31-2009
and how can i check and solve this?
9 More Discussions You Might Find Interesting
1. Cybersecurity
At the moment, I have three computers at home. I want to use boardband for my three computers. But I don't want to use network at home. I have been looking for a product which call OriNoCo USB Cilent. How do I connect to the internet with my computer??
If I post this in a wrong place, please... (0 Replies)
Discussion started by: him
0 Replies
2. IP Networking
Hi,
I have a laptop with a Linksys Wireless G PCMCIA card and a cable connection goin into a router and then a patch lead from the router going to a Linksys Wireless G access point IP 192.168.1.245 with DHCP disabled.
I can connect to the access point from the laptop, but how do I get the... (1 Reply)
Discussion started by: perleo
1 Replies
3. UNIX for Dummies Questions & Answers
I installed solaris 10 x86 on my dell laptop on a partition alongside windows xp. I am able to connect to the internet in xp with both my ethernet local area connection as well as through my wireless network card. But, however i do not have clue as to how to go about it in solaris.
i did not... (0 Replies)
Discussion started by: stakes20
0 Replies
4. Ubuntu
Hi,
I am a new to Ubuntu linux and trying to learn it. I am using ubuntu 10.04. I am getting problem in setting my wireless network. I set it up properly and was working fine. But suddenly it stopped working, though the wireless icon saying that it is connected, but can't load any page. I... (2 Replies)
Discussion started by: linux_learner
2 Replies
5. Ubuntu
I have a laptop running Ubuntu Netbook Remix.
What I want to do is use it to connect to my routers wifi, and then plug my desktop into the laptops ethernet port and be hooked to my routers network without any NAT or ICS.
Desktop>>>>>>Laptop/Wired>>Laptop/Wireless>>>>>Router
I want it to look... (6 Replies)
Discussion started by: schwasskin
6 Replies
6. Red Hat
Hi,
I am trying to set up a wireless internet connection on my centos OS (6). I can connect via the copper using the internal LAN but cannot get the wireless connection working.
The 2 files that I have configured are:
My wpa_supplicant.conf:
ctrl_interface=/var/run/wpa_supplicant... (1 Reply)
Discussion started by: Duffs22
1 Replies
7. Android
Good day, everybody! I have a mobile phone (LG Optimus L5) with Android 4.0.3 and a tablet (PocketBook SurfPad 2) with Android 4.1.1 and I have problem with wireless network on these devices. Laptops don't have such problem. My wireless network organisation is a modem connected with an access point... (11 Replies)
Discussion started by: qzxcvbnm
11 Replies
8. Ubuntu
I run lubuntu from usb (try lubuntu, it's not install on my pc )
And i try to connect to network
I see the network name
And i put the pass
But it's not connect..
I tried to open hot spot on my phone and try to connect and it's not connect
I have edumax n150
Try to install new driver -... (0 Replies)
Discussion started by: popcoern
0 Replies
9. Linux
I have created a bridge with nmcli between eth0 and wlan0
I use this procedure
sudo nmcli con add ifname br0 type bridge con-name br0
sudo nmcli con add type bridge-slave ifname eth0 master br0
sudo nmcli con add type bridge-slave ifname wlan0 master br0
sudo nmcli con modify br0... (1 Reply)
Discussion started by: Linusolaradm1
1 Replies
LEARN ABOUT NETBSD
bridge
BRIDGE(4) BSD Kernel Interfaces Manual BRIDGE(4)
NAME
bridge -- network bridge device
SYNOPSIS
pseudo-device bridge
DESCRIPTION
The bridge driver creates a logical link between two or more IEEE 802 networks that use the same (or ``similar enough'') framing format. For
example, it is possible to bridge Ethernet and 802.11 networks together, but it is not possible to bridge Ethernet and Token Ring together.
To use bridge, the administrator must first create the interface and configure the bridge parameters. The bridge is created using the
ifconfig(8) create subcommand. The learning and forwarding behavior and other parameters of a bridge are configured by the brconfig(8) util-
ity.
A bridge can be used to provide several services, such as a simple 802.11-to-Ethernet bridge for wireless hosts, and traffic isolation.
A bridge works like a switch, forwarding traffic from one interface to another. Multicast and broadcast packets are always forwarded to all
interfaces that are part of the bridge. For unicast traffic, the bridge learns which MAC addresses are associated with which interfaces and
will forward the traffic selectively.
The bridge driver implements the IEEE 802.1D Spanning Tree protocol (STP). Spanning Tree is used to detect and remove loops in a network
topology.
Transparent filtering for IP and IPv6 packets can be added with the kernel configuration option options BRIDGE_IPF.
When filtering is enabled, bridged packets will pass through the filter inbound on the originating interface and outbound on the appropriate
interfaces. ARP and REVARP packets are forwarded without being filtered and others that are not IP nor IPv6 packets are not forwarded when
filtering is enabled.
Note that packets to and from the bridging host will be seen by the filter on the interface with the appropriate address configured as well
as on the interface on which the packet arrives or departs.
SEE ALSO
etherip(4), options(4), brconfig(8), ipf(8)
HISTORY
The bridge driver first appeared in NetBSD 1.6.
AUTHORS
The bridge driver was originally written by Jason L. Wright <jason@thought.net> as part of an undergraduate independent study at the Univer-
sity of North Carolina at Greensboro.
This version of the bridge driver has been heavily modified from the original version by Jason R. Thorpe <thorpej@wasabisystems.com>.
BUGS
The bridge driver currently supports only Ethernet and Ethernet-like (e.g. 802.11) network devices, with exactly the same interface MTU size
as the bridge device.
The bridge driver currently does not support snooping via bpf(4).
BSD
January 9, 2010 BSD