smc2582w-b bridge and solaris 10 wireless network Post: 302282457

9 More Discussions You Might Find Interesting

1. Cybersecurity

Wireless Network

At the moment, I have three computers at home. I want to use boardband for my three computers. But I don't want to use network at home. I have been looking for a product which call OriNoCo USB Cilent. How do I connect to the internet with my computer?? If I post this in a wrong place, please...

2. IP Networking

Wireless-G network

Hi, I have a laptop with a Linksys Wireless G PCMCIA card and a cable connection goin into a router and then a patch lead from the router going to a Linksys Wireless G access point IP 192.168.1.245 with DHCP disabled. I can connect to the access point from the laptop, but how do I get the...

3. UNIX for Dummies Questions & Answers

solaris 10 wireless network setup

I installed solaris 10 x86 on my dell laptop on a partition alongside windows xp. I am able to connect to the internet in xp with both my ethernet local area connection as well as through my wireless network card. But, however i do not have clue as to how to go about it in solaris. i did not...

4. Ubuntu

Wireless network not working

Hi, I am a new to Ubuntu linux and trying to learn it. I am using ubuntu 10.04. I am getting problem in setting my wireless network. I set it up properly and was working fine. But suddenly it stopped working, though the wireless icon saying that it is connected, but can't load any page. I...

5. Ubuntu

Wireless Bridge/Repeater ?

I have a laptop running Ubuntu Netbook Remix. What I want to do is use it to connect to my routers wifi, and then plug my desktop into the laptops ethernet port and be hooked to my routers network without any NAT or ICS. Desktop>>>>>>Laptop/Wired>>Laptop/Wireless>>>>>Router I want it to look...

6. Red Hat

[SOLVED] Wireless Network Setup

Hi, I am trying to set up a wireless internet connection on my centos OS (6). I can connect via the copper using the internal LAN but cannot get the wireless connection working. The 2 files that I have configured are: My wpa_supplicant.conf: ctrl_interface=/var/run/wpa_supplicant...

7. Android

Problem with wireless network

Good day, everybody! I have a mobile phone (LG Optimus L5) with Android 4.0.3 and a tablet (PocketBook SurfPad 2) with Android 4.1.1 and I have problem with wireless network on these devices. Laptops don't have such problem. My wireless network organisation is a modem connected with an access point...

8. Ubuntu

Could not connect to wireless network

I run lubuntu from usb (try lubuntu, it's not install on my pc ) And i try to connect to network I see the network name And i put the pass But it's not connect.. I tried to open hot spot on my phone and try to connect and it's not connect I have edumax n150 Try to install new driver -...

9. Linux

Is possible to bridge wlan0 and eth0 using network manager?How to for wpa?

I have created a bridge with nmcli between eth0 and wlan0 I use this procedure sudo nmcli con add ifname br0 type bridge con-name br0 sudo nmcli con add type bridge-slave ifname eth0 master br0 sudo nmcli con add type bridge-slave ifname wlan0 master br0 sudo nmcli con modify br0...

LEARN ABOUT CENTOS

nm-connection-editor

NM-CONNECTION-EDITOR(1) 				      General Commands Manual					   NM-CONNECTION-EDITOR(1)

NAME

       nm-connection-editor - network connection editor for NetworkManager

SYNOPSIS

       nm-connection-editor  [ OPTIONS ]

DESCRIPTION

       nm-connection-editor  is  a  GTK-based application to add, remove, and modify network connections stored by NetworkManager.  NetworkManager
       must be running for any network connections to be added, removed, or modified.

OPTIONS

       -t, --type=<type>
	      Type of connection to create or show.  Values are NetworkManager setting names, eg  "802-3-ethernet",  "802-11-wireless",  "bridge",
	      "bond", "wimax", "infiniband", "vlan", etc.  Does nothing if --create or --show is not given.

       -s, --show
	      Expand or collapse the network list to highlight the network connection type given by --type.

       -c, --create
	      Create a new connection of the type given by --type and allow the user to modify connection details.

       -e, --edit=<uuid>
	      Show the network connection edit window for the connection of the given UUID.

SEE ALSO

       nmcli(1), NetworkManager(8), nm-applet(1).

								 15 February 2013					   NM-CONNECTION-EDITOR(1)