01-27-2009
I want to use SMIT to set static IP address on an AIX system
Good days every body,
I discovered this trea and I thougt that i could post my question on It.
I have acquired and IBM AIX system 4 months ago.
The system is configure in DHCP by default
I want some body to tell me step by step how to use SMIT to configure the whole system to Staitc IP.
I am a newbie to this system AIX.
I find it difficul to use the command line to configure the system.
I need your help.
Regards.
10 More Discussions You Might Find Interesting
1. HP-UX
***Newbie alert***
What's the easiest way to accomplish this? An admin left our company and I have taken over his HP Workstation and moved it to a different location that is on a different IP segment.
I have performed a number of google searches but the steps I have followed haven't worked.
... (1 Reply)
Discussion started by: Steelysteel
1 Replies
2. IP Networking
I have a USB Wireless Adapter using the rum0 driver. All I want to do is set a perminent static IP for the onboard wired interface elxl0. I can plumb the wired interface up fine on the fly, but when I try to save the static IP over a reboot, I lose the IP address assigned to rum0 from my wireless... (1 Reply)
Discussion started by: ts97783
1 Replies
3. IP Networking
I am trying to write a set of scripts for my Ubuntu 810 Server to allow a user to change from DHCP to a user-supplied Static IP, Subnet, Gateway and DNS Servers.
So far I have the following, where $USERCHOICE is a user-entered value in each case:
ifconfig eth0 down && ifconfig eth0 $USERCHOICE... (1 Reply)
Discussion started by: cleanden
1 Replies
4. Solaris
Hello friend, I am new in UNIX, but I want to learn a lot
Well I have a problem to try to configure my PC with a static IP Address
(IP 192.168.1.39, Mask 255.255.255.0, gateway 192.168.1.1)
(DNS 200.48.225.130 and 200.48.225.146).
where are the file that I must be change?
The SO is Sun Solaris... (15 Replies)
Discussion started by: andresguillen
15 Replies
5. Red Hat
Hi,
I am using RHEL 5.1 and i would like to know,
how to find the whether my system is using DHCP or STATIC IP
with out looking at /etc/sysconfig/network-scripts/ifconfig-eth0 configuration file.
Regards,
Venkat (3 Replies)
Discussion started by: venkat55
3 Replies
6. UNIX for Dummies Questions & Answers
Hey guys ,
YEs this is probably silly for most but i am new to this forum and solaris . i am curious to know if the ip address we have for our solaris server is static or dhcp . how can i tell ? will ifconfig -a tell me this ? or other commands?
Thanks in advance (1 Reply)
Discussion started by: xdrivex
1 Replies
7. Red Hat
Hi All,
Could you please explain the purpose of assigning the static IP by using the DHCP Concept. Like by using the clients MAC address we assign the static IP Address. Waiting for your reply. Thanks in Advance. (6 Replies)
Discussion started by: Sharath Kumar
6 Replies
8. HP-UX
Hi,
I can find the IP details whether it is Static or dynamic in Linux machine from the location /etc/sysconfig/network-scripts/ifconfig-eth0 configuration file.
Can someone suggest a location to find the same in HP UX machines?
-Vivek (2 Replies)
Discussion started by: vkk
2 Replies
9. IP Networking
I'm trying to figure out what circumstances would cause an Open Solaris 11.2 host to switch itself from a static to a DHCP ip address upon reboot. This has only happened once but is a cause for some concern as this machine will be part of a web server pool.
Nothing has changed on the LAN that... (2 Replies)
Discussion started by: SmokeyJoe
2 Replies
10. Solaris
We have 2 solaris 10 t5240 servers with static IP addresses on nxge0 I/F which were rebooted a few days back with a known good config that has been in place for years (for /etc/hosts, /etc/hostname.nxge0, /etc/netmasks, etc)
They are not using dhcp.
About the same time today, both of their... (7 Replies)
Discussion started by: hdatontodo
7 Replies
LEARN ABOUT DEBIAN
dh_auto_configure
DH_AUTO_CONFIGURE(1) Debhelper DH_AUTO_CONFIGURE(1)
NAME
dh_auto_configure - automatically configure a package prior to building
SYNOPSIS
dh_auto_configure [buildsystemoptions] [debhelperoptions] [--params]
DESCRIPTION
dh_auto_configure is a debhelper program that tries to automatically configure a package prior to building. It does so by running the
appropriate command for the build system it detects the package uses. For example, it looks for and runs a ./configure script,
Makefile.PL, Build.PL, or cmake. A standard set of parameters is determined and passed to the program that is run. Some build systems, such
as make, do not need a configure step; for these dh_auto_configure will exit without doing anything.
This is intended to work for about 90% of packages. If it doesn't work, you're encouraged to skip using dh_auto_configure at all, and just
run ./configure or its equivalent manually.
OPTIONS
See "BUILD SYSTEM OPTIONS" in debhelper(7) for a list of common build system selection and control options.
-- params
Pass params to the program that is run, after the parameters that dh_auto_configure usually passes. For example:
dh_auto_configure -- --with-foo --enable-bar
SEE ALSO
debhelper(7)
This program is a part of debhelper.
AUTHOR
Joey Hess <joeyh@debian.org>
9.20120909 2011-10-19 DH_AUTO_CONFIGURE(1)