01-23-2009
The SNMP daemon is launched at boot time by /etc/rc2.d/S85tcp.
So just fire up 'vi /etc/tcp' and comment our the relevant lines.
(You could have found this out with 'grep snmp /etc/rc2.d/*i'.)
10 More Discussions You Might Find Interesting
1. Linux
Hello,
is there a way to disable connection logging for a specific service? Or eventually to disable /var/log/secure in general?
Closed. Double post (0 Replies)
Discussion started by: TehOne
0 Replies
2. UNIX for Advanced & Expert Users
Hello,
is there a way to disable connection logging for a specific service? Or eventually to disable /var/log/secure in general? (2 Replies)
Discussion started by: TehOne
2 Replies
3. AIX
dear
how can i disable the SNMP service in AIX 6.1 . (2 Replies)
Discussion started by: thecobra151
2 Replies
4. HP-UX
hi everybody,
I can easily enable /disable the FTP service from SAM, how can I do this via command line? using inetd? how?
cheers,
messi (1 Reply)
Discussion started by: messi777
1 Replies
5. UNIX for Dummies Questions & Answers
Hello, am working on a suse linux system and trying to connect the server to the monitoring system we use. On checking the logs, i see that the snmp service is unavailable and would appreciate any help on how to fix this.
snmpd stop - done
snmpd start - done
snmpd status - unused (instead... (16 Replies)
Discussion started by: mena
16 Replies
6. Solaris
Hello everyone,
Can anyone help me to disable SNMP v1/2 authentification on Solaris 10 and use SNMP v3 authentification ?
I have SNMPv3 installed on my Solaris but the tool we use to scan vulnerabilities still show that there is a problem whith authentification version.
Does it mean that... (1 Reply)
Discussion started by: adilyos
1 Replies
7. UNIX for Dummies Questions & Answers
i am working with embedded system -Dell DCS management sub system. my question is as below:
currently we are using linux kernel 2.6.30 build and we have a kernel logs stored to the /var/log/messages path. now we have to transfer all this logs to the specified SNMP target as a part of SNMP... (4 Replies)
Discussion started by: vipul_prajapati
4 Replies
8. Solaris
Hi;
How can I disable or remove SNMPv1/2c authentication. I would like to use SNMP version 3 authentication.
bash-3.00# uname -a
SunOS SOL9229 5.10 Generic_142910-17 i86pc i386 i86pc
bash-3.00# (1 Reply)
Discussion started by: gc_sw
1 Replies
9. Solaris
I have a service that resides in both the global and non global zones. When I disable the service in the global zone, a svcs -p on that service shows the process name and ID of the svcadmd for the non global. An svcs -l on the service in the global shows online with an intended state of disabled.... (0 Replies)
Discussion started by: Cbrown31
0 Replies
10. Solaris
Hey everyone, so I recently installed sma and disabled snmpdx for system monitoring in Solarwinds on 7 Oracle servers running Solaris 10. It was running just fine until we had to shutdown all systems and power back up (hurricane). Since then I cannot get the sma service to start, it goes into... (4 Replies)
Discussion started by: Zeus18
4 Replies
LEARN ABOUT REDHAT
snmp-ups
snmp-ups(8) Network UPS Tools (NUT) snmp-ups(8)
NAME
snmp-ups - Driver for RFC 1628 SNMP UPS equipment
NOTE
This man page only documents the hardware-specific features of the snmp-ups driver. For information about the core driver, see nutups-
drv(8).
SUPPORTED HARDWARE
Any UPS that is RFC 1628 (UPS MIB) compliant.
EXPERIMENTAL DRIVER
This driver has been tagged experimental and is not built by default.
REQUIREMENTS
This driver needs UCD SNMP, aka Net-SNMP installed to compile successfully. See http://www.net-snmp.org/ for more information.
On Red Hat 7.2, these packages are required:
ucd-snmp-devel-4.2.3-1, ucd-snmp-4.2.3-1, ucd-snmp-utils-4.2.3-1
You must install SNMP-UPS-MIB.txt in your MIBs directory - typically /usr/share/snmp/mibs/, but it may vary from system to system. You can
generate this from chapter 4 of RFC 1628 (see http://www.faqs.org).
EXTRA ARGUMENTS
This driver supports the following optional settings in the ups.conf(5):
community=name
Set community name (default = public)
snmp_version=version
Set SNMP version (default = v1, the other allowed value is v2c)
INSTALLATION
This driver is not built by default. You can build it by using "configure --with-drivers=snmp-ups" before calling make.
IMPLEMENTATION
The hostname of the UPS is specified with the "port" value in ups.conf, i.e.:
[snmp]
driver = snmp-ups
port = snmp-ups.example.com
community = public
snmp_version = v1
SUPPORTED VARIABLES
INFO_MFR UPS Manufacturer
INFO_MODEL UPS Model
INFO_FIRMREV Firmware/Software Version
INFO_STATUS OFF, OL, OB, BOOST, TRIM
INFO_BATTPCT Battery percentage
INFO_RUNTIME Predicted runtime on battery
INFO_BATTVOLT Battery Voltage
INFO_OUTVOLT Output Voltage
PLANNED SUPPORT
INFO_UTILITY Input Voltage
INFO_ACFREQ AC Frequency
INFO_UPSTEM UPS Temperature
INFO_LOADPCT Load Percentage
CMD_? Not determined
AUTHORS
Arnaud Quette, Hans Ekkehard Plesser
SEE ALSO
The core driver:
nutupsdrv(8)
Internet resources:
The NUT (Network UPS Tools) home page: http://www.exploits.org/nut/
NUT mailing list archives and information: http://lists.exploits.org/
Tue Oct 22 2002 snmp-ups(8)