|
|
Sponsored Content
Top Forums
Shell Programming and Scripting
help me how to use nawk for required output
Post 302278374 by dodasajan on Tuesday 20th of January 2009 04:49:24 AM
01-20-2009
|
|
10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
I do a lot of command line scripting to capture data from files or other command output. I've checked in a number of Unix and scripting books but for the life of me I can't find out how to asign field data from nawk output into variables that I can manipulate later. For example, reading a two... (6 Replies)
Discussion started by: steveje0711
6 Replies
2. Shell Programming and Scripting
Hello friends,
I doing the follwing script , but found problem to store it to a shell variable.
#! /bin/sh
for temp in `find ./dat/vector/ -name '*.file'`
do
echo $temp
nawk -v temp=$temp 'BEGIN{ split(temp, a,"\/"); print a}'
done
output:
./dat/vector/drf_all_002.file... (6 Replies)
Discussion started by: user_prady
6 Replies
3. Shell Programming and Scripting
Hi
I have the following output
Message man amm (9196) is calling
Hello & Alert man amtrr (9197) is stopped
Find amfi (19198) is cancelled
Engine Item aea (19203) is notified
Engine Item2 aea2 ... (8 Replies)
Discussion started by: PrasannaKS
8 Replies
4. Shell Programming and Scripting
Hi,
I have a string in log file from that i need to pick the username.
the string is like this--
pid 2172 tid 3124: 160: 10110847: userName :
pid 2172 tid 3124: 160: 10110847: userName :
pid 2172 tid 3124: 160: 10110847: userName :
pid 2172 tid 3124: 160: 10110847: userName :
pid... (5 Replies)
Discussion started by: namishtiwari
5 Replies
5. Shell Programming and Scripting
I have searched and the answers I have found thus far have led me to this point, so I feel I am just about there.
I am trying to convert a column of hexadecimal to decimal values so that I can filter out via grep just the data I want. I was able to pull my original 3 character hex value and... (10 Replies)
Discussion started by: PCGameGuy
10 Replies
6. Shell Programming and Scripting
Legends,
I have 2 files f1 and f2. when i use nawk to compare the difference(subtraction) from 4th column of the file, it truncates the output.
can you please help to resolve this.
subtraction is (4th col of f1 - 4th col of f2). but it gives only below lines out of 116. I want to print all... (7 Replies)
Discussion started by: sdosanjh
7 Replies
7. Shell Programming and Scripting
Below script perfectly works, giving below mail output. BUT, I want to make the script mail only if there are any D-Defined/T-Transition/B-Broken State WPARs and also to copy the output generated during monitoring to a temporary log file, which gets cleaned up every week. Need suggestions.
... (4 Replies)
Discussion started by: aix_admin_007
4 Replies
8. Shell Programming and Scripting
I need a Korn shell script which does the folllowing:-
If there is one "|" (pipe) delimited file so, the script should check the 5th field to be blank or not. if it is a blank tht entire line of the file should be redirected to another file. if the 5th field is not blank it should pass that.
... (4 Replies)
Discussion started by: Juhi Kashyap
4 Replies
9. Shell Programming and Scripting
Hi All,
I am working on nawk script, has the small function which prints the output on the screen.Am trying to print/append the same output in a file.
Basically nawk script should print the output on the console/screen and as well it should write/append the same result to a file.
script :... (3 Replies)
Discussion started by: Optimus81
3 Replies
10. Shell Programming and Scripting
Hi
I have this command, which counts number of lines in a specific file and then prints it on screen.nawk 'NF{c++}END{print "Number of GPS coordinates in file: "c}' $filename
I would like to have the output put into a variable, but can't seem to find the correct argument for it.
How do I... (3 Replies)
Discussion started by: bulleteyedk
3 Replies
LEARN ABOUT ULTRIX
sact
sact(1) General Commands Manual sact(1) Name sact - display current SCCS file editing activity Syntax sact files Description The command informs the user of any impending deltas to a named SCCS file. This situation occurs when the command with the -e option has been previously executed without a subsequent execution of the command. If a directory is named on the command line, behaves as though each file in the directory were specified as a named file, except that non-SCCS files and unreadable files are silently ignored. If a name of - is given, the standard input is read with each line being taken as the name of an SCCS file to be processed. The output for each named file consists of five fields separated by spaces. Field 1 Specifies the SID of a delta that currently exists in the SCCS file to which changes will be made to make the new delta. Field 2 Specifies the SID for the new delta to be created. Field 3 Contains the login name of the user who will make the delta (that is, executed a for editing. Field 4 Contains the date that -e was executed. Field 5 Contains the time that -e was executed. Diagnostics See for explanations. See Also delta(1), get(1), sccs(1), sccshelp(1), unget(1), sccsfile(5)) Guide to the Source Code Control System sact(1)