01-17-2009
Quote:
Originally Posted by
incredible
seg, you're slow
just now he didn't even had the "-", then he edited that
haha, doh! just started the daily forum browsing.
OP: look i think you're going about this whole thing the wrong way. If both drivers were the same size and vendor then a copy of the partition table (using slize 2!) would be fine, but given the situation as I understand it you should just run format and manually set the partition table to match as needed. It's not terribly complicated.
10 More Discussions You Might Find Interesting
1. Solaris
Hi
I'm having a big trouble running a configuration tool (ftamtool) which uses xview on sunos 5.8, it refuses to start and says: XView error: could not load font 'FONT_FAMILY_SANS_SERIF...
How to force the program to use installed fonts and where are fonts installed available to use ?
... (0 Replies)
Discussion started by: andryk
0 Replies
2. Solaris
Error is like
/users/d12381/check.sh: mail_sysadmin@mycompany: not found
Plz help me to sort out this issue (6 Replies)
Discussion started by: Renjesh
6 Replies
3. Solaris
If i have diks layout like below
0 root wm 0 - 634 471.29MB (635/0/0)
965200
1 var wm 635 - 2014 1.00GB (1380/0/0)
2097600
2 backup wm 0 - 2732 1.98GB (2733/0/0)
4154160
3 swap wu 2015 - 2704 ... (1 Reply)
Discussion started by: tpx99
1 Replies
4. HP-UX
Hi,
I would like to ask for your help. I tried to log in through console to my server HP-UX 10.20 but I keep receiving error message as below:
Vxfs: mesg 001: vx_nospace -/dev/vg02/lvol6 file system full
Vxfs: mesg 001: vx_nospace - /dev/vg02/lvol9 file system full
How should I stop this... (4 Replies)
Discussion started by: yeazas
4 Replies
5. Solaris
Hi All,
when i run the command prtvtoc the output shows
38309 cylinders
38307 accessible cylinders
as per my undertanding the 1st cylinder is used for storing the vtoc , how about the second cylinder ? where its used and for what purpose?
Thanks (9 Replies)
Discussion started by: kumarmani
9 Replies
6. Shell Programming and Scripting
Hi,
I have an command which find the files modified within last 8 days and then after selecting the files from the location it make the tar format and send it to the specified destination ...now I want that this task to be automative ..that is it should happen after every 5 minutes ...for that... (3 Replies)
Discussion started by: NARESH SAXENA
3 Replies
7. Solaris
Hello,
I have a X86 server (solaris 10) with 4 similar disks. One of these 4 disks is the root disk.
I need to create a mirror disk to the root disk and two hot spares using the remaining 3 disks.
However, when I use the fmthard commad, I am getting the below error:
root@xxxxxxxx>prtvtoc... (5 Replies)
Discussion started by: mystition
5 Replies
8. Shell Programming and Scripting
if ; then
rm -rf "${x}"_"${y}"_abc_pqr.dat error: `then' unmatchedCan anyone please help me in correcting it.
Please use code tags next time for your code and data. Thanks (2 Replies)
Discussion started by: D_Sethi
2 Replies
9. Solaris
Hi,
I am trying to mirror a disk (which was already mirror and after breaking it, doing it again). This is root disk and in control of veritas. Somehow, slice information is not coming correctly on this. Can somebody give some pointer to fix it ?
root@tdrp091:/root# prtvtoc /dev/rdsk/c3t0d0s2 |... (6 Replies)
Discussion started by: solaris_1977
6 Replies
10. Solaris
Hi,
It is Solaris-10 with ZFS. c0t1d0 is original disk. c0t0d0 was faulty disk, which was replaced with new one and by mistake somebody ran opposite command
# prtvtoc /dev/rdsk/c0t0d0s0 | fmthard -s - /dev/rdsk/c0t1d0s0
Now rpool is in suspended state. Right now server is up, but allowing ssh... (6 Replies)
Discussion started by: solaris_1977
6 Replies
LEARN ABOUT MINIX
repartit
REPARTITION(8) System Manager's Manual REPARTITION(8)
NAME
repartition - load a partition table
SYNOPSIS
repartition device [partition-file]
DESCRIPTION
Repartition uploads a new partition table for the partitions of device. The table is obtained from the first sector of partition-file if
given, device otherwise. Device may refer to the whole drive or a primary partition, depending on whether you want to upload a partition
or a subpartition table. The partitions will be truncated to fit within the enclosing device like the disk driver does, unless the numbers
are coming from partition-file.
EXAMPLES
repartition /dev/hd0
repartition /dev/hd4 /etc/hd4.table
Reload the partition table of drive 0 setting /dev/hd[1-4], and the subpartition table of /dev/hd4 setting /dev/hd4[a-d] using a file. The
latter may be useful if you need more than the 4 subpartitions a single Minix partition gives you.
DIAGNOSTICS
The new table is printed on standard output.
FILES
/dev/hd[0-9]
SEE ALSO
hd(4), part(8).
BUGS
The disk must be in use for the changes to stick. The partition table of an idle disk will be reloaded on the first open.
AUTHOR
Kees J. Bot (kjb@cs.vu.nl)
REPARTITION(8)