Sponsored Content
Operating Systems Solaris Solaris BigAdmin RSS hotlink - Network Interface Monitoring Post 302276459 by Linux Bot on Tuesday 13th of January 2009 09:20:09 PM
Old 01-13-2009
hotlink - Network Interface Monitoring

Script to check speed/duplex/settings/health and vlan information for network interfaces.

More...
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt (4 Replies)
Discussion started by: witt
4 Replies

2. UNIX for Advanced & Expert Users

network interface problem

Hi expert, Need some help on network interface issue.. I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies

3. IP Networking

How to activate a network interface?

What are the steps between "ifconfig eth0 UP" and "net_device->open"? ifconfig eth0 UP => ioctl(skfd, SIOCSIFFLAGS, &ifr) (ifr.ifr_flags = IFF_UP | IFF_RUNNING) => ????? => what are these steps? net_device->open Thanks! (1 Reply)
Discussion started by: samuncle
1 Replies

4. Solaris

Network interface configuration

Dears, i follow this to configure Network interface for my PC O/S : Unix Sun Solaris vi /etc/hostname.bge0 and write my ip vi /etc/netmasks and write my subnetmask vi /etc/defautrouter and write my gatwey vi /etc/resolv.conf and write my DNS after i reboot My Computer ... (3 Replies)
Discussion started by: jenovaux
3 Replies

5. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

6. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies

7. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies

8. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
URI::URL(3pm)						User Contributed Perl Documentation					     URI::URL(3pm)

NAME
URI::URL - Uniform Resource Locators SYNOPSIS
$u1 = URI::URL->new($str, $base); $u2 = $u1->abs; DESCRIPTION
This module is provided for backwards compatibility with modules that depend on the interface provided by the "URI::URL" class that used to be distributed with the libwww-perl library. The following differences exist compared to the "URI" class interface: o The URI::URL module exports the url() function as an alternate constructor interface. o The constructor takes an optional $base argument. The "URI::URL" class is a subclass of "URI::WithBase". o The URI::URL->newlocal class method is the same as URI::file->new_abs. o URI::URL::strict(1) o $url->print_on method o $url->crack method o $url->full_path: same as ($uri->abs_path || "/") o $url->netloc: same as $uri->authority o $url->epath, $url->equery: same as $uri->path, $uri->query o $url->path and $url->query pass unescaped strings. o $url->path_components: same as $uri->path_segments (if you don't consider path segment parameters) o $url->params and $url->eparams methods o $url->base method. See URI::WithBase. o $url->abs and $url->rel have an optional $base argument. See URI::WithBase. o $url->frag: same as $uri->fragment o $url->keywords: same as $uri->query_keywords o $url->localpath and friends map to $uri->file. o $url->address and $url->encoded822addr: same as $uri->to for mailto URI o $url->groupart method for news URI o $url->article: same as $uri->message SEE ALSO
URI, URI::WithBase COPYRIGHT
Copyright 1998-2000 Gisle Aas. perl v5.14.2 2012-02-11 URI::URL(3pm)
All times are GMT -4. The time now is 10:44 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy