01-13-2009
hotlink - Network Interface Monitoring
Script to check speed/duplex/settings/health and vlan information for network interfaces.
More...
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
3. IP Networking
What are the steps between "ifconfig eth0 UP" and "net_device->open"?
ifconfig eth0 UP =>
ioctl(skfd, SIOCSIFFLAGS, &ifr) (ifr.ifr_flags = IFF_UP | IFF_RUNNING) =>
????? => what are these steps?
net_device->open
Thanks! (1 Reply)
Discussion started by: samuncle
1 Replies
4. Solaris
Dears,
i follow this to configure Network interface for my PC
O/S : Unix Sun Solaris
vi /etc/hostname.bge0
and write my ip
vi /etc/netmasks
and write my subnetmask
vi /etc/defautrouter
and write my gatwey
vi /etc/resolv.conf
and write my DNS
after i reboot My Computer ... (3 Replies)
Discussion started by: jenovaux
3 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT DEBIAN
ns_absoluteurl
Ns_Url(3aolserver) AOLserver Library Procedures Ns_Url(3aolserver)
__________________________________________________________________________________________________________________________________________________
NAME
Ns_AbsoluteUrl, Ns_ParseUrl, Ns_RelativeUrl, Ns_SkipUrl - URL manipulation routines
SYNOPSIS
#include "ns.h"
int
Ns_AbsoluteUrl(Ns_DString *pds, char *url, char *baseurl)
int
Ns_ParseUrl(char *url, char **pprotocol, char **phost,
char **pport, char **ppath, char **ptail)
char *
Ns_RelativeUrl(char *url, char *location)
char *
Ns_SkipUrl(Ns_Request *request, int n)
_________________________________________________________________
DESCRIPTION
Ns_AbsoluteUrl(pds, url, baseurl)
Construct an URL based on baseurl but with as many parts of the incomplete url as possible. Return NS_OK or NS_ERROR.
Ns_ParseUrl(url, pprotocol, phost, pport, ppath, ptail)
Parse a URL into its component parts. Pointers to the protocol, host, port, path, and "tail" (last path element) will be set by ref-
erence in the passed-in pointers. The passed-in url will be modified.
Ns_RelativeUrl(url, location)
If the url passed in is for this server, then the initial part of the URL is stripped off. e.g., on a server whose location is
http://www.foo.com, Ns_RelativeUrl of "http://www.foo.com/hello" will return "/hello". Returns a pointer to the beginning of the
relative url in the passed-in url, or NULL if error. Will set errno on error.
Ns_SkipUrl(request, n)
Return a pointer n elements into the request's url.
SEE ALSO
nsd(1), info(n)
KEYWORDS
AOLserver 4.0 Ns_Url(3aolserver)