01-10-2009
firstly check all your mount points with df -k and try accessing them. Check format output and iostat -En and see if there are any hard errors on the disk. "Device is gone" not necessarily be an internal disk.We need more outputs to verify.
10 More Discussions You Might Find Interesting
1. Solaris
Hello,
I am trying to do mirror in solaris 9. I have total 0-7 disks
4 5 6 7
0 1 2 3
Drive 0 and Drive 4 = Boot Drives
Need to Mirror following drives.
Drive 1 and Drive 5 = Need to mirror
Drive 1 was mounted on: /prod1, /prod2, /prod3, /prod4, /prod5.
Then i... (3 Replies)
Discussion started by: deal732
3 Replies
2. Solaris
solaris os run on X86.
bootdisk have been mirrored.but there is one disk miss,I want to replace the fail disk,but after I replace the disk,the system can't boot!
pls help! (2 Replies)
Discussion started by: netxjman
2 Replies
3. Solaris
I installed Solaris 10 on this Dell 5150 with only 1 SATA hard drive setup, all went well, and I could view the disk in the disk management window.
However, I setup a 2nd hard drive, identical to 1st drive. Solaris wont recognize it and gives an error when trying to view disks in disk management... (5 Replies)
Discussion started by: Joncamp
5 Replies
4. UNIX for Dummies Questions & Answers
Hi Guys,
I'm looking for a way to monitor disk health/status for a Solaris 5.8 sparc machine. I'm looking for something similar to LSIutility or MegaCLI.
Any suggestions?
Output of `modinfo`:
30 102616fb 10be8 118 1 ssd (SCSI SSA/FCAL Disk Driver 1.151)
122 7821c000 18550 32 1 ... (2 Replies)
Discussion started by: tank126
2 Replies
5. Solaris
Need a procedure document to do "root disk mirroring in solaris volume manager for solaris 10". I hope some one will help me asap. I need to do it production environment.
Let me know if you need any deatils on this.
Thanks,
Rama (1 Reply)
Discussion started by: ramareddi16
1 Replies
6. Solaris
Hi all,
I guess most of you have seen this error message while installing Solaris 10 on an x86 platform. I got the error message while installing from DVD ISO on my home VMWare ESXi server.
It took me a long time to figure the exact issue and a subsequent solution. the solution is very... (1 Reply)
Discussion started by: admin_xor
1 Replies
7. Solaris
I have a solaris 10 system configured using NetApp as its storage, and the file systems are already configured as you can see from the example below:
root@moneta # df -h
Filesystem size used avail capacity Mounted on
/dev/md/dsk/d0 9.8G 513M 9.3G 6% /
... (0 Replies)
Discussion started by: fretagi
0 Replies
8. Solaris
I have a solaris 10 system configured using NetApp as its storage, and the file systems are already configured as you can see from the example below:
root@moneta # df -h
Filesystem size used avail capacity Mounted on
/dev/md/dsk/d0 9.8G 513M 9.3G 6% /... (4 Replies)
Discussion started by: fretagi
4 Replies
9. Solaris
Hi all,
OS is Solaros 10 Sparc
While doing Netbackup upgradation to 7.5 , the server was asked to reboot.
But then it came up in single user mode,
and after I typed format command it showed some disk error.
bash-3.00# format
Searching for disks...WARNING:... (2 Replies)
Discussion started by: manalisharmabe
2 Replies
10. Solaris
Hello,
We are running solaris 8 and there is a disk having problem with consistency
The following devices (soft partitions from NetApp are inconsistent, unable to be repaired with fsck and need to be restored:
root@server1 # df -k
Filesystem kbytes used ... (4 Replies)
Discussion started by: gull05
4 Replies
LEARN ABOUT CENTOS
nfsiostat
nfsiostat(8) System Manager's Manual nfsiostat(8)
NAME
nfsiostat - Emulate iostat for NFS mount points using /proc/self/mountstats
SYNOPSIS
nfsiostat [[<interval>] [<count>]] [<options>][<mount_point>]
DESCRIPTION
The nfsiostat command displays NFS client per-mount statisitics.
<interval>
specifies the amount of time in seconds between each report. The first report contains statistics for the time since each file sys-
tem was mounted. Each subsequent report contains statistics collected during the interval since the previous report.
<count>
If the <count> parameter is specified, the value of <count> determines the number of reports generated at <interval> seconds apart.
if the interval parameter is specified without the <count> parameter, the command generates reports continuously.
<options>
Define below
<mount_point>
If one or more <mount point> names are specified, statistics for only these mount points will be displayed. Otherwise, all NFS
mount points on the client are listed.
OPTIONS
-a or --attr
displays statistics related to the attribute cache
-d or --dir
displays statistics related to directory operations
-h or --help
shows help message and exit
-l LIST or --list=LIST
only print stats for first LIST mount points
-p or --page
displays statistics related to the page cache
-s or --sort
Sort NFS mount points by ops/second
--version
show program's version number and exit
FILES
/proc/self/mountstats
SEE ALSO
iostat(8), mountstats(8), nfsstat(8)
AUTHOR
Chuck Lever <chuck.lever@oracle.com>
15 Apr 2010 nfsiostat(8)