|
|
Sponsored Content
Operating Systems
AIX
AIX / Etherchannel / VLANs
Post 302275118 by jwholey on Friday 9th of January 2009 10:11:25 AM
01-09-2009
|
|
10 More Discussions You Might Find Interesting
1. AIX
I'm trying to configure Etherchannel on AIX 5.3 and I'm having some problems. I am aggregating both of the onboard NIC's (ent0 and ent1) into a new adapter ent2 for failover reasons obviously. At first I was experiencing a problem where about 50% of all my packets would be dropped. Then after... (4 Replies)
Discussion started by: acascianelli
4 Replies
2. IP Networking
Hi All,
I'm trying to configure a vlan interface, to do this I'm using the following command "vconfig add eth0 20". I have my interface up and running, but when I test it using "ping -I eth0.20 192.168.1.1" and in other console use "tcpdump -i eth0.20" I can not see any tagged frame.
... (0 Replies)
Discussion started by: lagigliaivan
0 Replies
3. AIX
Hello,
On a partition with AIX 5300-11-01-0944.
1 etherchannel ent9 with aggregation ent3/ent7.
# lsdev |grep ent
...
ent3 Available 07-01 4-Port 10/100/1000 Base-TX PCI-Express Adapter (14106803)
...
ent7 Available 0A-01 4-Port 10/100/1000 Base-TX PCI-Express... (2 Replies)
Discussion started by: Trunk
2 Replies
4. AIX
I have one p5 server, no lpar, 2 physical network adapter, bundle as one EtherChannel. The two 2 physical network adapter connect to 2 network switches.
How to make this as a redundancy config?
Current is if one physical network adapter down, the seond one will go through the network. but if... (2 Replies)
Discussion started by: rainbow_bean
2 Replies
5. UNIX for Dummies Questions & Answers
Hi Gurus,
Can anyone explain me what is a Vlan and a Native vlan. How to check the native Vlan on my server having a solaris10 OS.
Thanks in advance.:) (2 Replies)
Discussion started by: rama krishna
2 Replies
6. AIX
Hi,
I have a AIX5.3 P6-520 with 8x1Gb Ethernet ports with possible connections to 2 CISCO 2960 switches.
I can create 8023ad Etherchannels which work correctly with the switches (I have set up for LACP passive and a valid channels)
But can create 2x 8023ad 4Gb Etherchannels with no backups.... (2 Replies)
Discussion started by: spitzie
2 Replies
7. AIX
Hi Guys,
I am trying to test an etherchannel failover and switchback.
I did failover from primary to backup adapter, but now I am not able to switch it back to primary.
phcxxxxx:/ > entstat -d ent4 | grep Active
Active channel: backup adapter ... (1 Reply)
Discussion started by: snchaudhari2
1 Replies
8. Solaris
I've been given an IP address to assign to an ldom that is in a different subnet than the host, and I am looking for assistance in getting it online. I believe I need "VLAN tagging" as found in this link, but I do not understand all of the terminology.
My host machine is on subnet 10.25.112.x,... (1 Reply)
Discussion started by: bstring
1 Replies
9. IP Networking
Hey everyone. I work in a data center, and I'm working on getting my CCNA. Now when I read articles on the idea of VLAN's it makes sense. Especially if you have multiple switches daisy chained in multiple locations. My two main questions though are that most of these examples use PC's as examples... (2 Replies)
Discussion started by: Lost in Cyberia
2 Replies
10. Proxy Server
In a "typical" data centre environment (telco, financial services etc), would a Linux OS typically have one IP address connected to one VLAN or would it have many IPs and/or VLANs. I say "Linux OS" as I'm referring to an instance of the OS not necessarily a Host or server. Think Linux OS = VM in a... (9 Replies)
Discussion started by: PCB
9 Replies
LEARN ABOUT REDHAT
vconfig
VCONFIG(8) System Manager's Manual VCONFIG(8) NAME
vconfig - VLAN (802.1q) configuration program. SYNOPSIS
vconfig [lots of long options] DESCRIPTION
The vconfig program allows you to create and remove vlan-devices on a vlan enabled kernel. Vlan-devices are virtual ethernet devices which represents the virtual lans on the physical lan. OPTIONS
add [interface-name] [vlan-id] Creates a vlan-device on [interface-name]. The resulting vlan-device will be called according to the nameing convention set. rem [vlan-device] Removes the named vlan-device. set_flag [vlan-device] 0 | 1 When 1, ethernet header reorders are turned on. Dumping the device will appear as a common ethernet device without vlans. When 0(default) however, ethernet headers are not reordered, which results in vlan tagged packets when dumping the device. Usually the default gives no problems, but some packet filtering programs might have problems with it. set_egress_map [vlan-device] [skb-priority] [vlan-qos] This flags that outbound packets with a particular skb-priority should be tagged with the particular vlan priority vlan-qos. The default vlan priority is 0. set_ingress_map [vlan-device] [skb-priority] [vlan-qos] This flags that inbound packets with the particular vlan priority vlan-qos should be queued with a particular skb-priority. The default skb-priority is 0. set_name_type VLAN_PLUS_VID | VLAN_PLUS_VID_NO_PAD | DEV_PLUS_VID | DEV_PLUS_VID_NO_PAD Sets the way vlan-device names are created. Use vconfig without arguments to see the different formats. NOTES VLAN will use Broadcom's NICE interface when the network device supports it. This is necessary, since usually the hardware of these devices already removes the vlan tag from the ethernet packet. The set_flag option on vlan-devices created on such a physical net- work device will be ignored. Dumping the network-device will show only untagged(non-vlan) traffic, and dumping the vlan-devices will only show traffic intended for that vlan, without the tags. FILES
/proc/net/vlan/config /proc/net/vlan/[vlan-device] SEE ALSO
ip(8), ifconfig(8) AUTHORS
This manual page was written by Ard van Breemen <ard@kwaak.net> The vlan patch is written by Ben Greear <greearb@candelatech.com> VCONFIG(8)