01-06-2009
have you tried another nic on the server in the same switch/port/config? you could have a bad nic. also, have you checked w/ your network team on how the switch port is configured?
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
We are trying to Establish Network using Linux.Now we are facing the problem in configring Ethernet.In out network we are giving eth0 in server and activating it at the boot time,so it is activating as it is but when we define the Ethernet of node on server and allowing it to activate at boot time... (5 Replies)
Discussion started by: at_renai2001
5 Replies
2. UNIX for Dummies Questions & Answers
I am using Red Hat 7.1 . I have installed one Server and trying to make network installing workstations on other system of a network. The Ethernet of the server has been mounted and working properly. I am getting problem installing /mounting the Ethernet of the workstations .I have tryed this by... (1 Reply)
Discussion started by: at_renai2001
1 Replies
3. Cybersecurity
I suspect that someone is using a sniffer on my Ethernet connection,
OS X 10.3.9, DSL,
ok, I'm in terminal using the "ifconfig" command >
flags=8049<UP,LOOPBACK,RUNNING,MULTICAST>mtu 16384
right, it's not in "promiscuous mode", but i think it's Trojaned, can anyone point me in the... (1 Reply)
Discussion started by: su"do"er
1 Replies
4. UNIX for Advanced & Expert Users
I understand that one should setup virtual ethernet adapters in the lpars which is the best way for various lpars to communicate with each other - Does anyone have info on this or can point me to a doc that explains how to set this up? (1 Reply)
Discussion started by: capeme
1 Replies
5. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
6. Solaris
Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args:
SunOS Release 5.8 Version Generic_108528-29 64-bit
Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.
ifconfig: plumb: qfe2: Bad file number
configuring IPv4 interfaces: eri0.
moving addresses... (1 Reply)
Discussion started by: fredginting
1 Replies
7. Solaris
my solris box network is unreachable how to solve this
ipaddress assiagning and entry in vi /etc/host
how to solve network is unreachable (2 Replies)
Discussion started by: tirupathi
2 Replies
8. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
9. Linux
I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.
Here's what I did:
created file /etc/modprobe.d/bonding.d and added the following to it:
alias bond0 bonding
options bonding... (2 Replies)
Discussion started by: dr_mabuse
2 Replies
LEARN ABOUT REDHAT
tc589_cs
3C589_CS(4) Kernel Interfaces Manual 3C589_CS(4)
NAME
3c589_cs - 3Com 3c589 Etherlink III device driver
SYNOPSIS
insmod 3c589_cs.o [pc_debug=n] [if_port=n] [irq_list=i,j,...]
DESCRIPTION
3c589_cs is the low-level Card Services driver for the 3Com 3c589 PCMCIA ethernet adapter and 3Com 3c562/3c563 combo cards. When this
driver is attached to a card, it allocates the next available ethernet device (eth0..eth#). This device name will be reported in the ker-
nel log file, and passed on to cardmgr(8).
With the default transceiver setting, the driver will attempt to continuously autodetect the transceiver type (10base2 or 10baseT). There
should normally only be a one or two second lag before the correct transceiver is selected. On particularly noisy or busy networks, it is
possible for the detection logic to incorrectly toggle the transceiver type. If this becomes a problem, it may be necessary to explicitly
select the interface type when the module is loaded or with the ifport command.
PARAMETERS
pc_debug=n
Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero
value enables debugging.
if_port=n
Selects the transceiver type. 0 is autodetect (10baseT or 10base2), 1 is 10baseT (twisted pair), 2 is 10base2 (BNC, or thin net).
and 3 is AUI (thick ethernet). The default is 0 (autodetect).
irq_list=i,j,...
Specifies the set of interrupts that may be allocated by this driver.
DIAGNOSTICS
eth#: interrupt(s) dropped!
Indicates that the driver did not receive an interrupt notification for some reason. The driver will poll the card (with a signifi-
cant performance penalty) if the problem persists. The most likely cause is an interrupt conflict and/or host bridge configuration
problem.
AUTHOR
David Hinds - dahinds@users.sourceforge.net
SEE ALSO
cardmgr(8), pcmcia(5), ifport(8).
pcmcia-cs 2000/06/12 21:24:48 3C589_CS(4)